why does my Ford F-150 13th Generation (2015-2020) hesitate when I accelerate

Ford F-150 13th Generation (2015-2020)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

561 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix engine hesitation during acceleration in Ford F-150 13th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening any parts related to the engine or fuel system.

Symptoms

•Engine stalling during acceleration
•Rough or uneven acceleration
•Poor throttle response
•Check engine light illuminated
•Decreased fuel efficiency
•Increased emissions

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any fault codes.
2
Check the fuel pressure using a fuel pressure gauge to ensure proper fuel delivery.
3
Inspect the air intake system for blockages, leaks, or damaged components.
4
Examine the throttle body for carbon buildup or malfunctions.
5
Test the ignition system components, including spark plugs and ignition coils.
6
Inspect the transmission fluid level and condition, as transmission issues can contribute to acceleration problems.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Fuel pressure gauge
•Throttle body cleaner
•Socket set
•Torque wrench
•Spark plug socket

Parts Required

•Fuel filter
•Fuel pump (if necessary)
•Spark plugs
•Ignition coils (if necessary)
•Transmission fluid (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any fault codes.
2
Check the fuel pressure using a fuel pressure gauge to ensure proper fuel delivery.
3
Inspect the air intake system for blockages, leaks, or damaged components.
4
Examine the throttle body for carbon buildup or malfunctions.
5
Test the ignition system components, including spark plugs and ignition coils.
6
Inspect the transmission fluid level and condition, as transmission issues can contribute to acceleration problems.

Solution

1. Preparation

Gather tools and parts needed for repairs.
Disconnect the battery to ensure safety while working on electrical components.

2. Inspect and Clean Throttle Body

Remove the air intake duct to access the throttle body.
Use throttle body cleaner and a soft cloth to clean the throttle plate and surrounding area.
Reinstall the air intake duct securely.

3. Fuel System Inspection

If fuel pressure was low in the diagnostic step, replace the fuel filter.
If necessary, replace the fuel pump by following these steps:
1. Relieve fuel system pressure.
2. Disconnect the negative battery terminal.
3. Remove the fuel pump access panel (if applicable) or lower the fuel tank.
4. Disconnect fuel lines and electrical connectors from the fuel pump.
5. Remove the retaining ring and lift the fuel pump out of the tank.
6. Install the new pump in reverse order, ensuring all connections are secure.

4. Spark Plug and Ignition Coil Replacement

Remove the engine cover if present.
Disconnect the ignition coil connector and remove the coil using a socket set.
Remove the spark plug using a spark plug socket, inspect for wear, and replace if necessary.
Install new spark plugs (torque to manufacturer specifications) and ignition coils.

5. Transmission Fluid Check

Check the transmission fluid level using the dipstick.
If fluid is low, add the correct type of transmission fluid. If dirty or burnt, consider changing the transmission fluid and filter.