why does my Honda Accord 9th Generation (2013-2017) make a clicking noise when turning?

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

583 words

Problem Statement

Learn to diagnose and fix the clicking noise when turning in Honda Accord 9th Generation (2013-2017). Step-by-step guide with tools and parts required.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical systems.
•Use jack stands to support the vehicle securely when working underneath.

Symptoms

•Clicking noise when turning the steering wheel
•Possible vibration felt in the steering wheel
•Noise may increase with speed or sharper turns
•Decreased handling performance
•Potential loss of power steering assist

Diagnostic Steps

1
Inspect the front axle and CV joints for any visible damage or wear.
2
Check the condition of the wheel bearings for play or roughness.
3
Examine the suspension components (control arms, bushings, struts) for wear or damage.
4
Test the power steering system for proper fluid levels and leaks.
5
Listen for noises while turning during a test drive to isolate the source of the clicking.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Pry bar
•CV joint boot kit
•Bearing puller
•Fluid pump

Parts Required

•CV joint (if damaged)
•Wheel bearings (if worn)
•Suspension components (if necessary)
•Power steering fluid

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front axle and CV joints for any visible damage or wear.
2
Check the condition of the wheel bearings for play or roughness.
3
Examine the suspension components (control arms, bushings, struts) for wear or damage.
4
Test the power steering system for proper fluid levels and leaks.
5
Listen for noises while turning during a test drive to isolate the source of the clicking.

Solution

1. Preparation

Gather tools and materials.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical components.

2. Inspect and Replace CV Joints

Tools Required: Socket set, torque wrench, pry bar, CV joint boot kit (if needed)
Raise the front of the vehicle using a jack and secure it on jack stands.
Remove the wheel on the affected side.
Use a socket to remove the axle nut and disconnect the CV joint from the hub.
Inspect the CV joint for damage; if worn or damaged, replace it.
Reassemble by reversing the disassembly steps, ensuring correct torque values for the axle nut.

3. Check and Replace Wheel Bearings

Tools Required: Bearing puller, socket set, torque wrench
While the wheel is removed, check for play in the wheel bearing by moving the hub side to side.
If play is detected, remove the hub assembly and use a bearing puller to extract the old bearing.
Install the new bearing, ensuring it is seated properly.
Reassemble the hub and wheel, following torque specifications.

4. Inspect Suspension Components

Tools Required: Socket set, pry bar, torque wrench
Check for wear on control arms, bushings, and struts.
Replace any damaged components.
Use a torque wrench to tighten all bolts to the manufacturer specifications.

5. Check Power Steering System

Tools Required: Fluid pump, power steering fluid
Inspect the power steering fluid reservoir for proper levels.
If low, top off with the correct type of power steering fluid.
Check for leaks in hoses and connections and replace any damaged hoses.