why does my Honda CR-V Fifth Generation (2017-2022) make a loud noise when turning

Honda CR-V Sixth Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

564 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Discover how to diagnose and fix loud noise when turning in Honda CR-V (2017-2022). Step-by-step guide with symptoms, diagnostic steps, and solutions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Ensure the vehicle is securely lifted and supported before working underneath.

Symptoms

•Loud clunking or grinding noise during turns
•Difficulty steering or increased resistance when turning
•Vibration in the steering wheel while turning
•Uneven tire wear
•Warning lights on the dashboard (e.g., ESC or ABS light)

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage or wear on the CV joints and axles.
3
Perform a visual inspection of the suspension components (control arms, bushings, struts).
4
Examine the wheel bearings for play or noise.
5
Test drive the vehicle while listening for noise changes in different turning scenarios.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Wrench
•Funnel
•Container for old fluid
•Socket set
•Torque wrench
•Pry bar
•Ball joint separator
•Bearing puller

Parts Required

•Power steering fluid
•CV joints or axles (if necessary)
•Suspension components (if necessary)
•Wheel bearings (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage or wear on the CV joints and axles.
3
Perform a visual inspection of the suspension components (control arms, bushings, struts).
4
Examine the wheel bearings for play or noise.
5
Test drive the vehicle while listening for noise changes in different turning scenarios.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery for safety.

2. Inspect and Replace Power Steering Fluid

Tools Required: Wrench, funnel, container for old fluid.
Check the power steering fluid reservoir for proper fluid level and quality.
If the fluid is low or contaminated, drain the old fluid into a container and refill with manufacturer-recommended power steering fluid.

3. Inspect and Replace CV Joints/Axles (if necessary)

Tools Required: Socket set, pry bar, torque wrench.
Raise the vehicle using a jack and secure it with jack stands.
Remove the wheel and inspect the CV joint boots for tears or leaks.
If damaged, remove the axle nut and disconnect the axle from the hub.
Replace with a new axle or CV joint, ensuring to torque the axle nut to the manufacturer’s specification.

4. Examine and Replace Suspension Components (if necessary)

Tools Required: Socket set, torque wrench, ball joint separator.
Inspect control arms, bushings, and struts for wear.
If components are worn, remove the old parts using a socket set and ball joint separator.
Install new suspension components, torquing to the manufacturer’s specifications.

5. Check and Replace Wheel Bearings (if necessary)

Tools Required: Bearing puller, socket set, torque wrench.
Remove the wheel and brake assembly to access the hub.
Check for any play in the wheel bearings by wiggling the hub.
If worn, replace the bearings by removing the hub and pressing in new bearings.