why does my Volkswagen Golf MK7 (2015-2019) make a clicking noise when I accelerate

Volkswagen Golf MK8.5 (2024-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

512 words

Problem Statement

Discover how to diagnose and fix the clicking noise during acceleration in Volkswagen Golf MK7 (2015-2019). Step-by-step guide with diagnostic steps and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical systems.
•Allow the engine to cool before performing any work.

Symptoms

•Clicking noise when accelerating
•Noise occurs during low-speed acceleration
•Vibration felt through the steering wheel
•Possible loss of power during acceleration
•Noise may vary with speed or turning

Diagnostic Steps

1
Inspect the CV joints and axle shafts for wear or damage.
2
Check the engine and transmission mounts for signs of wear or failure.
3
Examine the suspension components, including struts and bushings, for any loose or damaged parts.
4
Perform a visual inspection of the exhaust system for loose components that may rattle.
5
Test drive the vehicle while turning left and right to see if the noise changes with directional changes.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Pry bar
•Suspension tool kit

Parts Required

•CV joints (if damaged)
•Engine/transmission mounts (if needed)
•Suspension components (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints and axle shafts for wear or damage.
2
Check the engine and transmission mounts for signs of wear or failure.
3
Examine the suspension components, including struts and bushings, for any loose or damaged parts.
4
Perform a visual inspection of the exhaust system for loose components that may rattle.
5
Test drive the vehicle while turning left and right to see if the noise changes with directional changes.

Solution

1. Preparation

Ensure the vehicle is parked on a level surface and the engine is turned off.
Gather tools and safety equipment.

2. Inspect and Replace CV Joints

Tools Required: Jack and jack stands, socket set, torque wrench, pry bar.
Steps:
1. Lift the vehicle using a jack and secure it with jack stands.
2. Remove the wheel on the affected side.
3. Inspect the CV boot for any tears or leaks; if damaged, replace the CV joint.
4. Use a pry bar to detach the CV joint from the wheel hub, then remove it from the transmission.
5. Install the new CV joint, ensuring it is properly seated, and torque all bolts to manufacturer specifications.
6. Reinstall the wheel and lower the vehicle.

3. Check and Replace Engine/Transmission Mounts

Tools Required: Socket set, torque wrench, pry bar.
Steps:
1. Inspect the engine and transmission mounts for cracks or separation.
2. If damaged, remove the old mounts by unbolting them from the engine block and chassis.
3. Install new mounts, ensuring they are aligned properly and torque the bolts to manufacturer specifications.

4. Inspect and Replace Suspension Components

Tools Required: Socket set, torque wrench, suspension tool kit.
Steps:
1. Inspect all suspension components for wear, especially the struts and bushings.
2. Replace any worn parts, ensuring alignment is correct after installation.
3. Torque all suspension bolts to manufacturer specifications.