how to fix the lane departure warning system on my Ford Explorer Fifth Generation (2011-2019)

Ford Explorer Fifth Generation (2011-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

510 words

Problem Statement

Learn how to diagnose and fix lane departure warning system issues in Ford Explorer (2011-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Electrical

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems to avoid shock or short circuits.

Symptoms

•Lane departure warning light illuminated on the dashboard
•Inconsistent alerts when changing lanes
•No alerts when crossing lane markings
•System not activating during driving
•Possible camera or sensor obstruction alerts

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any related faults.
2
Inspect the front-facing camera and sensors for dirt, debris, or damage.
3
Check the lane departure warning system settings in the vehicle's menu.
4
Verify the calibration of the camera and sensors.
5
Inspect wiring and connections related to the camera and sensors for corrosion or damage.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Soft cloth
•Cleaning solution
•Multimeter
•Professional scan tool

Parts Required

•Replacement wires or connectors

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any related faults.
2
Inspect the front-facing camera and sensors for dirt, debris, or damage.
3
Check the lane departure warning system settings in the vehicle's menu.
4
Verify the calibration of the camera and sensors.
5
Inspect wiring and connections related to the camera and sensors for corrosion or damage.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the negative battery terminal to prevent electrical shock.

2. Clean the Camera and Sensors

Tools Required: Soft cloth, cleaning solution.
Sub-steps:
1. Locate the front-facing camera, typically mounted near the rearview mirror or on the windshield.
2. Use the soft cloth and cleaning solution to gently clean the lens of the camera and any visible sensors.
3. Ensure no obstructions are present that could impede the camera's view.

3. Check and Adjust System Settings

Tools Required: Vehicle’s owner manual.
Sub-steps:
1. Turn on the vehicle and navigate to the settings menu on the infotainment system.
2. Access the driver assistance settings and ensure that the lane departure warning system is enabled.
3. Adjust sensitivity settings as needed based on user preference.

4. Recalibrate the Camera and Sensors

Tools Required: Professional scan tool (if needed).
Sub-steps:
1. Follow the manufacturer's procedure for recalibrating the lane departure warning system. This may involve using a scan tool to initiate calibration.
2. Perform the calibration as per instructions in the vehicle’s service manual. This often requires driving the vehicle in a straight line for a specified distance.

5. Inspect and Repair Wiring

Tools Required: Multimeter, wire strippers, soldering iron (if needed).
Sub-steps:
1. Trace the wiring harness connected to the camera and sensors.
2. Use a multimeter to check for continuity in the wires.
3. Repair or replace any damaged wires or connectors to ensure proper function.