how to fix P0700 code in Ford F-150 12th Generation (2009-2014)

Ford F-150 12th Generation (2009-2014)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0700

3 min read

535 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0700 transmission control malfunction in Ford F-150 (2009-2014). Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0700

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine and transmission to cool before working on them.

Symptoms

•Check engine light illuminated
•Harsh or erratic shifting
•Transmission slipping
•Reduced acceleration or power
•Delay in shifting into gear

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0700 and any other related codes.
2
Inspect the transmission fluid level and condition; look for signs of contamination or burnt odor.
3
Check the wiring and connectors related to the transmission control module (TCM) for damage or corrosion.
4
Test the TCM for proper function using a multimeter to measure voltage and ground signals.
5
Inspect the transmission control solenoids for proper operation.
6
Check for any mechanical issues within the transmission assembly that may trigger the code.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Multimeter
•Electronic cleaner
•Fluid pump

Parts Required

•Transmission fluid (Ford MERCON LV)
•Transmission filter and gasket
•Transmission control solenoids
•Transmission control module

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0700 and any other related codes.
2
Inspect the transmission fluid level and condition; look for signs of contamination or burnt odor.
3
Check the wiring and connectors related to the transmission control module (TCM) for damage or corrosion.
4
Test the TCM for proper function using a multimeter to measure voltage and ground signals.
5
Inspect the transmission control solenoids for proper operation.
6
Check for any mechanical issues within the transmission assembly that may trigger the code.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and secure it with wheel chocks.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Check Transmission Fluid

Remove the transmission dipstick (if applicable) and check fluid level.
If low, add the recommended transmission fluid (Ford MERCON LV).
If the fluid is dirty or burnt, perform a transmission fluid and filter change.

3. Inspect Wiring and Connectors

Locate the TCM and inspect the wiring harness for frayed wires or corrosion.
Disconnect the TCM connector and clean the terminals with electronic cleaner.
Reconnect the wiring and ensure a tight fit.

4. Test Transmission Control Module (TCM)

Use a multimeter to check the voltage at the TCM connector.
Compare readings with the specifications in the service manual.
If readings are out of range, replace the TCM.

5. Replace Transmission Control Solenoids

Remove the transmission pan using a socket set; drain the fluid.
Replace defective transmission control solenoids as needed.
Reinstall the pan with a new gasket and torque bolts to manufacturer specifications (typically 12-15 ft-lbs).

6. Clear Codes and Test Drive

Reconnect the negative battery terminal.
Use the OBD-II scanner to clear the P0700 code.
Perform a test drive to ensure that the issue is resolved.