how to fix P0700 transmission code in my Ford F-150 12th Generation (2009-2014)

Ford F-150 12th Generation (2009-2014)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0700

3 min read

588 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0700 transmission code in Ford F-150 12th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0700

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the transmission pan to prevent burns.

Symptoms

•Check engine light illuminated
•Rough or erratic shifting
•Delayed engagement when shifting from park to drive
•Transmission slipping
•Poor acceleration or loss of power
•Transmission overheating

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any specific transmission-related codes.
2
Check the transmission fluid level and condition; look for signs of contamination or burning.
3
Inspect the wiring and connectors for the transmission control module (TCM) for damage or corrosion.
4
Verify the operation of the transmission range sensor (neutral safety switch) and ensure it is functioning correctly.
5
Test the TCM for proper operation using a multimeter to check for voltage and ground signals.
6
Inspect the transmission for any obvious leaks or mechanical issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Multimeter
•Drain pan

Parts Required

•Transmission fluid (Ford-approved ATF)
•Transmission filter
•Transmission range sensor (if faulty)
•TCM (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any specific transmission-related codes.
2
Check the transmission fluid level and condition; look for signs of contamination or burning.
3
Inspect the wiring and connectors for the transmission control module (TCM) for damage or corrosion.
4
Verify the operation of the transmission range sensor (neutral safety switch) and ensure it is functioning correctly.
5
Test the TCM for proper operation using a multimeter to check for voltage and ground signals.
6
Inspect the transmission for any obvious leaks or mechanical issues.

Solution

1. Preparation

Gather tools and parts.
Disconnect the negative battery terminal to prevent electrical shorts.
Ensure the vehicle is on a flat surface and secure it with wheel chocks.

2. Fluid Check and Replacement

Check Fluid Level
- Remove the transmission dipstick and wipe it clean.
- Reinsert and remove the dipstick again to check the fluid level.
- If low, add the recommended ATF type as per the owner’s manual.
Fluid Change (if needed)
- Place a drain pan under the transmission.
- Remove the transmission pan bolts and lower the pan carefully, allowing old fluid to drain.
- Replace the transmission filter and clean the mating surfaces.
- Reinstall the pan and torque the bolts to the specified value (typically around 12-16 ft-lbs).

3. Wiring and Sensor Repair

Inspect Wiring
- Visually inspect the wiring harness leading to the TCM and transmission for any signs of wear, fraying, or corrosion.
- Repair or replace damaged wires and connectors as necessary.
Replace Transmission Range Sensor
- Disconnect the electrical connector from the transmission range sensor.
- Remove the mounting bolts and carefully take out the sensor.
- Install the new sensor and reconnect the electrical connector.

4. TCM Testing and Replacement (if faulty)

Test TCM
- Use a multimeter to check voltage at the TCM connectors.
- If readings are outside the specifications, consider replacing the TCM.
Replace TCM
- Disconnect the battery again.
- Remove any mounting brackets or screws holding the TCM in place.
- Install the new TCM and reconnect all wiring.
- Reconnect the battery.