how to fix P0700 code on Ford F-150 13th Generation (2015-2020)

Ford F-150 13th Generation (2015-2020)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0700

3 min read

542 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0700 transmission issues in Ford F-150 (2015-2020). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Error Code

P0700

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool down before opening any components.

Symptoms

•Check engine light illuminated
•Harsh or erratic shifting
•Transmission slipping or failing to engage
•Poor acceleration or power loss
•Increased fuel consumption

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0700 and check for any additional transmission-related codes.
2
Inspect the transmission fluid level and condition; look for contamination or burnt smell.
3
Visually inspect the wiring and connectors to the Transmission Control Module for damage or corrosion.
4
Test the TCM using a multimeter to ensure it is receiving the correct voltage signals.
5
Conduct a road test to monitor transmission behavior and verify symptoms.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Wire stripper/crimper
•Transmission fluid pump
•Funnel
•Drain pan

Parts Required

•Transmission fluid (specific to Ford specifications)
•Transmission Control Module (if replacement is necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0700 and check for any additional transmission-related codes.
2
Inspect the transmission fluid level and condition; look for contamination or burnt smell.
3
Visually inspect the wiring and connectors to the Transmission Control Module for damage or corrosion.
4
Test the TCM using a multimeter to ensure it is receiving the correct voltage signals.
5
Conduct a road test to monitor transmission behavior and verify symptoms.

Solution

1. Preparation

Gather tools and parts needed.
Disconnect the negative battery terminal to ensure safety.
Allow the vehicle to cool down if it has been running.

2. Check and Replace Transmission Fluid

Sub-steps:
1. Locate the transmission dipstick (if equipped) and remove it.
2. Check the fluid level; add the appropriate type of transmission fluid (consult owner’s manual for specifications) if low.
3. If fluid is contaminated, proceed to a complete fluid change.
Tools Required: Transmission fluid pump, funnel, drain pan, socket set.

3. Inspect and Repair Wiring

Sub-steps:
1. Visually inspect the wiring harness connected to the TCM and transmission for signs of wear or damage.
2. Repair any damaged wires using solder and heat-shrink tubing or replace the affected harness.
3. Ensure that all connectors are secure and free from corrosion.
Tools Required: Wire stripper/crimper, multimeter, soldering iron.

4. Replace the Transmission Control Module (if necessary)

Sub-steps:
1. Locate the TCM, usually found near the transmission or under the dashboard.
2. Disconnect the electrical connectors from the TCM.
3. Remove the mounting bolts and take out the old TCM.
4. Install the new TCM, ensuring all connections are secure.
5. Reconnect the negative battery terminal.
Tools Required: Socket set, screwdrivers.

5. Clear Codes and Test

Sub-steps:
1. Use the OBD-II scanner to clear the P0700 code and any related codes.
2. Conduct a road test to ensure the transmission operates smoothly and monitor for any warning lights.