my Genesis G70 IG (2017-2023) is jerking when shifting what causes this

Genesis G70 IG (2017-2023)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

488 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission jerking issues in Genesis G70 (2017-2023). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before opening the transmission.

Symptoms

•Jerking or harsh shifting during acceleration
•Delay in response when shifting gears
•Transmission slipping or unexpected RPM fluctuations
•Check engine light may be illuminated
•Poor fuel economy

Diagnostic Steps

1
Scan the vehicle's computer system for diagnostic trouble codes (DTCs) using an OBD-II scanner.
2
Inspect the transmission fluid level and condition (check for discoloration or burnt smell).
3
Verify that the transmission fluid filter is not clogged.
4
Check for any visible leaks in the transmission or surrounding areas.
5
Test the throttle position sensor (TPS) and mass airflow sensor (MAF) for accurate readings.
6
Inspect engine and transmission mounts for wear or damage.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Transmission fluid pump
•Torque wrench
•Drain pan

Parts Required

•Transmission fluid (Hyundai SP-IV ATF)
•Transmission filter
•Transmission pan gasket
•Throttle position sensor (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's computer system for diagnostic trouble codes (DTCs) using an OBD-II scanner.
2
Inspect the transmission fluid level and condition (check for discoloration or burnt smell).
3
Verify that the transmission fluid filter is not clogged.
4
Check for any visible leaks in the transmission or surrounding areas.
5
Test the throttle position sensor (TPS) and mass airflow sensor (MAF) for accurate readings.
6
Inspect engine and transmission mounts for wear or damage.

Solution

1. Preparation

Gather necessary tools and components.
Ensure the vehicle is parked on a level surface.
Disconnect the battery to avoid electrical issues during repair.

2. Check and Change Transmission Fluid

Sub-steps:
1. Remove the transmission fluid dipstick. Check the fluid level and condition.
2. If fluid is low or contaminated, drain the old fluid using a drain pan.
3. Replace the transmission fluid with the manufacturer-recommended fluid type (e.g., Hyundai SP-IV ATF).
4. Refill with new transmission fluid through the dipstick tube to the correct level.

3. Replace Transmission Filter

Sub-steps:
1. Remove the transmission pan bolts using a socket set and carefully lower the pan.
2. Remove the old transmission filter and replace it with a new one.
3. Clean the transmission pan and replace the gasket with a new one.
4. Reattach the pan and torque bolts to the manufacturer specifications (typically around 10-12 ft-lbs).

4. Inspect and Replace Throttle Position Sensor (if faulty)

Sub-steps:
1. Locate the throttle position sensor on the throttle body.
2. Disconnect the electrical connector and remove the sensor.
3. Install the new throttle position sensor and connect the electrical connector.
4. Clear any codes from the vehicle’s computer and perform a throttle relearn procedure if necessary.