GMC Sierra T1XX (2019-Present) engine makes a knocking noise when accelerating, what's the cause?

GMC Sierra T1XX (2019-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

579 words

Problem Statement

Learn how to diagnose and fix engine knocking noise in GMC Sierra T1XX (2019-Present). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow engine to cool before opening any components.

Symptoms

•Knocking noise from the engine during acceleration
•Loss of power when accelerating
•Possible rough idle at low RPMs
•Increased oil consumption
•Check engine light may illuminate

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any logged faults.
2
Inspect the engine oil level and condition; check for signs of contamination or low oil.
3
Perform a visual inspection of the engine components, including the intake and exhaust systems.
4
Listen for the knocking noise in different RPM ranges to determine if it changes with load.
5
Check for loose or damaged components, such as exhaust heat shields or engine mounts.
6
Conduct a compression test on each cylinder to evaluate internal engine health.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Compression gauge
•Socket set
•Torque wrench
•Oil dipstick
•Funnel

Parts Required

•Engine oil (SAE 0W-20 or as specified by the manufacturer)
•Spark plugs (if worn or damaged)
•Timing chain or belt (if inspection shows wear)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any logged faults.
2
Inspect the engine oil level and condition; check for signs of contamination or low oil.
3
Perform a visual inspection of the engine components, including the intake and exhaust systems.
4
Listen for the knocking noise in different RPM ranges to determine if it changes with load.
5
Check for loose or damaged components, such as exhaust heat shields or engine mounts.
6
Conduct a compression test on each cylinder to evaluate internal engine health.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Disconnect the battery to prevent electrical shorts.
Allow the engine to cool down before starting work.

2. Inspect Engine Oil

Sub-steps:
1. Remove the oil dipstick and wipe it clean.
2. Insert the dipstick back into the tube and pull it out to check the oil level.
3. If oil is low, top off with the manufacturer-recommended oil type (e.g., SAE 0W-20).
4. If oil appears contaminated, consider an oil change.
Tools Required: Oil dipstick, funnel.

3. Check Engine Components

Sub-steps:
1. Remove engine covers if applicable for better access.
2. Visually inspect the spark plugs for wear or damage; replace if necessary.
3. Inspect the timing chain or belt for wear; replace if there is significant slack or damage.
4. Tighten any loose bolts or components found during inspection.
Tools Required: Socket set, torque wrench.

4. Compression Test

Sub-steps:
1. Remove spark plugs for access to the cylinder.
2. Insert a compression gauge into the spark plug hole of each cylinder.
3. Crank the engine and record the compression readings.
4. Compare readings to manufacturer specifications; replace any cylinder with low compression.
Tools Required: Compression gauge, socket set.

5. Reassemble and Test

Sub-steps:
1. Reinstall any components removed during inspection.
2. Reconnect the battery.
3. Start the engine and allow it to reach operating temperature.
4. Observe for any knocking noises and check for any leaks.
Tools Required: None additional from previous steps.