how to fix steering wheel shake when braking on Honda Accord 9th Generation (2013-2017)

Honda Accord 10th Generation (2018-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

539 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to fix steering wheel shake when braking in Honda Accord 2013-2017. Step-by-step guide with diagnostic steps and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical components.
•Allow the vehicle to cool down before working on the brake system to prevent burns.

Symptoms

•Steering wheel vibrates during braking
•Pulsation felt through the brake pedal
•Vehicle pulls to one side when braking
•Uneven wear on brake pads or tires
•Increased stopping distance

Diagnostic Steps

1
Inspect brake pads and rotors for uneven wear or damage.
2
Check for loose or worn suspension components (e.g., control arms, tie rods).
3
Perform a visual inspection of the wheel alignment and tire condition.
4
Measure rotor thickness and check for warping using a dial indicator.
5
Scan for any error codes that may indicate an issue with the ABS system.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Micrometer or dial indicator

Parts Required

•Brake pads
•Brake rotors (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake pads and rotors for uneven wear or damage.
2
Check for loose or worn suspension components (e.g., control arms, tie rods).
3
Perform a visual inspection of the wheel alignment and tire condition.
4
Measure rotor thickness and check for warping using a dial indicator.
5
Scan for any error codes that may indicate an issue with the ABS system.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Wear safety goggles and gloves.

2. Lift the Vehicle

Use a jack to lift the front of the vehicle and secure it on jack stands.
Remove the front wheels using a socket set.

3. Inspect and Replace Brake Components

Inspect Brake Pads and Rotors:
- Check for uneven wear on the brake pads.
- Measure rotor thickness with a micrometer; replace if below specifications (usually 1.0 mm over minimum thickness).
Replace Brake Rotors (if warped or worn):
- Remove the caliper bracket bolts using a socket set.
- Carefully slide the caliper off the rotor and secure it to avoid stress on the brake line.
- Remove the rotor by unscrewing any retaining screws or pulling directly off.
- Install new rotors, ensuring they are properly seated.
Replace Brake Pads:
- Remove old brake pads from the caliper bracket.
- Install new pads, ensuring they fit correctly into the bracket and that the wear indicators are in the correct positions.

4. Reassemble and Torque Components

Reattach the caliper bracket and torque bolts to manufacturer specifications (typically around 25-30 ft-lbs).
Reinstall wheels and hand-tighten lug nuts before lowering the vehicle.
Lower the vehicle and then torque lug nuts in a crisscross pattern to the specified value (usually 80-100 ft-lbs).

5. Test Drive

Start the vehicle and perform a test drive to check for vibrations during braking.
Monitor brake performance and listen for unusual noises.