how to fix P0700 code in Honda Accord 9th Generation (2013-2017)

Honda Accord 11th Gen (2023-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0700

3 min read

571 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0700 transmission control system malfunction in Honda Accord 2013-2017. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0700

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working on the transmission fluid to avoid burns.

Symptoms

•Check engine light illuminated
•Transmission slipping or hard shifting
•Unresponsive transmission
•Increased fuel consumption
•Rough idle when in gear

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm the P0700 code and any related codes.
2
Inspect transmission fluid level and condition; look for contamination or burnt smell.
3
Check the wiring and connectors related to the transmission control module (TCM) for any signs of damage or corrosion.
4
Test the TCM using a multimeter to ensure it is receiving proper voltage and ground signals.
5
Inspect the transmission range sensor (also known as the neutral safety switch) for proper function and alignment.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Fluid extraction tool
•Multimeter
•Socket set
•Torque wrench

Parts Required

•Honda ATF DW-1 transmission fluid
•Transmission filter (if applicable)
•Transmission range sensor (if faulty)
•Transmission control module (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm the P0700 code and any related codes.
2
Inspect transmission fluid level and condition; look for contamination or burnt smell.
3
Check the wiring and connectors related to the transmission control module (TCM) for any signs of damage or corrosion.
4
Test the TCM using a multimeter to ensure it is receiving proper voltage and ground signals.
5
Inspect the transmission range sensor (also known as the neutral safety switch) for proper function and alignment.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Disconnect the negative battery terminal to ensure safety while working on the electrical components.

2. Transmission Fluid Inspection

Tools Required: Fluid extraction tool (if necessary), funnel.
Check the transmission fluid level using the dipstick. If low, add the appropriate Honda ATF DW-1 fluid.
If the fluid is dark or has a burnt smell, proceed to change the transmission fluid and filter.
Sub-steps:
- Remove the transmission drain plug and drain the old fluid into a suitable container.
- Replace the transmission filter if applicable.
- Reinstall the drain plug and fill with new Honda ATF DW-1 fluid to the correct level.

3. TCM Inspection

Tools Required: Multimeter.
Reconnect the battery and test the TCM.
Sub-steps:
- Use a multimeter to check the voltage at the TCM connector while the ignition is ON. Compare readings to specifications in the service manual.
- If there is no power, trace the wiring back to the fuse and battery.

4. Repair or Replace Components

If faulty, replace the transmission range sensor or TCM as necessary.
Sub-steps:
- For the TCM, disconnect the wiring harness and remove the mounting bolts. Install the new TCM and reconnect the harness.
- For the transmission range sensor, locate it on the transmission, disconnect the wiring, and remove the mounting bolts. Install the new sensor and reconnect the wiring.

5. Final Checks

Clear the codes from the OBD-II scanner.
Reconnect the negative battery terminal.