how to check for EPS system failures in Honda Accord 9th Generation (2013-2017)

Honda Accord Eleventh Generation (2023-present)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

3 min read

592 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix EPS system failures in Honda Accord 9th Generation (2013-2017). Step-by-step guide with symptoms and solutions.

Affected Component

Steering

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on the electrical systems
•Ensure the vehicle is securely supported if working underneath

Symptoms

•EPS warning light illuminated on the dashboard
•Increased steering effort or stiffness
•Intermittent or complete loss of power steering assistance
•Unusual noises while turning the steering wheel
•Steering wheel vibration or play when driving

Diagnostic Steps

1
Scan for error codes using OBD-II scanner
2
Inspect EPS fuse for continuity and replace if blown
3
Measure the battery voltage to ensure it is within the normal range
4
Test EPS motor and controller for proper voltage and ground signals
5
Visually inspect the wiring harness and connectors for damage
6
Perform a steering angle sensor calibration using a diagnostic tool

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Torque wrench

Parts Required

•EPS fuse (if blown)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using OBD-II scanner
2
Inspect EPS fuse for continuity and replace if blown
3
Measure the battery voltage to ensure it is within the normal range
4
Test EPS motor and controller for proper voltage and ground signals
5
Visually inspect the wiring harness and connectors for damage
6
Perform a steering angle sensor calibration using a diagnostic tool

Solution

1. Preparation

Tools Required: OBD-II scanner, multimeter, socket set, torque wrench.
Ensure the vehicle is parked on a flat surface and the ignition is turned off before beginning any work.

2. EPS Fuse Replacement

Locate the Fuse Box: Find the fuse box under the dashboard on the driver's side.
Remove the EPS Fuse: Use a fuse puller to remove the EPS fuse and inspect it.
Replace if Necessary: If the fuse is blown, replace it with a new one of the same amperage.

3. Battery Voltage Check

Measure Voltage: Using a multimeter, connect the positive lead to the positive battery terminal and the negative lead to the negative terminal.
Evaluate Reading: If the voltage is below 12.4 volts, charge or replace the battery.

4. EPS Motor and Controller Test

Access EPS Motor: Remove any necessary covers to gain access to the EPS motor wiring.
Test Voltage: With the ignition on (engine off), measure the voltage at the EPS connector. It should be near battery voltage.
Check Ground: Ensure the ground connection is secure and has continuity.

5. Wiring and Connector Inspection

Visual Inspection: Look for frayed wires, corrosion, or loose connectors in the EPS system wiring.
Secure Connections: Repair or replace any damaged wiring or connectors.

6. Steering Angle Sensor Calibration

Use Diagnostic Tool: Connect the OBD-II scanner and navigate to the EPS module.
Follow Calibration Steps: Select the option to calibrate the steering angle sensor and follow on-screen instructions.