how to fix Honda Accord 9th Generation (2013-2017) that shakes when idling?

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

4 min read

628 words

Problem Statement

Learn how to diagnose and fix shaking at idle in Honda Accord 9th Generation (2013-2017). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Ensure the engine is cool before performing any repairs to avoid burns.

Symptoms

•Check engine light illuminated
•Rough idle or vibration felt in the cabin
•Decreased fuel efficiency
•Possible engine stalling
•Unusual noises from the engine compartment
•Increased emissions

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any engine-related issues.
2
Inspect engine mounts for wear or damage, as worn mounts can cause excessive vibration.
3
Check the air intake system for blockages or leaks.
4
Evaluate the condition of the spark plugs and ignition coils; replace if necessary.
5
Test for vacuum leaks using a smoke machine or carburetor cleaner around vacuum lines.
6
Measure fuel pressure to ensure the fuel system is delivering the proper amount of fuel.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Jack stands
•Smoke machine
•Carburetor cleaner

Parts Required

•Engine mounts
•Spark plugs
•Ignition coils
•Vacuum hoses (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any engine-related issues.
2
Inspect engine mounts for wear or damage, as worn mounts can cause excessive vibration.
3
Check the air intake system for blockages or leaks.
4
Evaluate the condition of the spark plugs and ignition coils; replace if necessary.
5
Test for vacuum leaks using a smoke machine or carburetor cleaner around vacuum lines.
6
Measure fuel pressure to ensure the fuel system is delivering the proper amount of fuel.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Disconnect the negative battery cable to prevent electrical shorts.
Allow the engine to cool down if it has been running.

2. Replace Worn Engine Mounts

Tools Required: Socket set, torque wrench, jack stands.
Sub-steps:
1. Lift the vehicle with a jack and secure it on jack stands.
2. Locate the engine mounts; typically found on the front, rear, and sides of the engine.
3. Remove the bolts securing the engine mount to the engine and the frame using the socket set.
4. Carefully lift the engine slightly using the jack to relieve pressure on the mount.
5. Remove the old engine mount and replace it with a new one.
6. Torque the bolts to the manufacturer-recommended specifications (usually around 40-60 ft-lbs).
7. Repeat for any additional mounts that require replacement.

3. Replace Spark Plugs and Ignition Coils

Tools Required: Socket set, torque wrench, dielectric grease.
Sub-steps:
1. Remove the engine cover if applicable.
2. Disconnect the ignition coil connectors and remove the coils by unscrewing them.
3. Remove the spark plugs using a spark plug socket.
4. Install new spark plugs, ensuring they are gapped correctly (refer to the owner’s manual for specifications).
5. Apply dielectric grease to the ignition coil boot before reinstallation.
6. Reinstall the ignition coils and reconnect the electrical connectors.

4. Check for Vacuum Leaks

Tools Required: Smoke machine or carburetor cleaner.
Sub-steps:
1. Start the engine and let it idle.
2. Use a smoke machine to introduce smoke into the intake system; watch for smoke escaping from any vacuum hoses or gaskets.
3. If using carburetor cleaner, spray around the vacuum lines and listen for changes in idle speed.
4. Replace any damaged hoses or gaskets found during this inspection.