how to fix loud wheel bearing noise in Honda Accord 9th Generation (2013-2017)

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

665 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix loud wheel bearing noise in Honda Accord 2013-2017. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the vehicle to cool before working on the brakes or wheel assembly.

Symptoms

•Continuous humming or grinding noise that increases with vehicle speed
•Vibration felt through the steering wheel or floor
•Noise changes when turning left or right
•Uneven tire wear observed
•Possible ABS warning light activation

Diagnostic Steps

1
Perform a visual inspection of the tires and wheel assemblies for any noticeable damage or wear.
2
Lift the vehicle using a jack and secure it on jack stands, then spin each wheel by hand to listen for noise or feel for roughness.
3
Use a stethoscope or mechanic's stethoscope to pinpoint the source of the noise by listening to the wheel hubs while rotating the wheels.
4
Check for any play in the wheel bearings by grasping the wheel at the 12 and 6 o'clock positions and attempting to rock it back and forth.
5
Inspect brake components for any signs of abnormal wear or damage that could contribute to noise.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Lug wrench
•Jack
•Jack stands
•Socket set
•Torque wrench
•Bearing press or hammer
•Mechanic's stethoscope

Parts Required

•New wheel bearing (specific for Honda Accord 2013-2017)
•Brake rotor (if necessary)
•Brake pads (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Perform a visual inspection of the tires and wheel assemblies for any noticeable damage or wear.
2
Lift the vehicle using a jack and secure it on jack stands, then spin each wheel by hand to listen for noise or feel for roughness.
3
Use a stethoscope or mechanic's stethoscope to pinpoint the source of the noise by listening to the wheel hubs while rotating the wheels.
4
Check for any play in the wheel bearings by grasping the wheel at the 12 and 6 o'clock positions and attempting to rock it back and forth.
5
Inspect brake components for any signs of abnormal wear or damage that could contribute to noise.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the battery for safety.

2. Remove Wheel

Tools Required: Lug wrench, jack, jack stands
Sub-steps:
1. Loosen the lug nuts slightly while the vehicle is on the ground.
2. Jack up the vehicle and secure it on jack stands.
3. Remove the lug nuts completely and take off the wheel.

3. Remove Brake Components

Tools Required: Socket set, torque wrench
Sub-steps:
1. Remove the caliper bolts using the socket set; hang the caliper using a bungee cord or wire (do not let it hang by the brake line).
2. Remove the brake rotor by taking off any retaining screws or clips.

4. Remove Wheel Hub Assembly

Tools Required: 12-point socket set, impact wrench (optional), bearing puller
Sub-steps:
1. Remove any cotter pin and nut securing the axle shaft to the hub.
2. Detach the wheel hub assembly from the steering knuckle by removing the bolts with a socket set.
3. Carefully pull the hub assembly off the axle shaft.

5. Install New Wheel Bearing

Tools Required: Bearing press or hammer, new wheel bearing
Sub-steps:
1. Press the new wheel bearing into the hub assembly using a bearing press; ensure it is seated properly.
2. Reinstall the wheel hub assembly onto the axle shaft and secure it with the nut and cotter pin.

6. Reassemble Brake Components

Tools Required: Torque wrench
Sub-steps:
1. Reattach the brake rotor and secure it with screws or clips.
2. Reinstall the brake caliper and tighten the bolts to the manufacturer's specifications using a torque wrench.

7. Reattach Wheel and Lower Vehicle

Tools Required: Lug wrench
Sub-steps:
1. Place the wheel back onto the hub and hand-tighten the lug nuts.
2. Lower the vehicle and then torque the lug nuts to the manufacturer's specifications.