how to tell if my Honda Accord 9th Generation (2013-2017) has a bad fuel pump

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

602 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix fuel pump issues in Honda Accord 2013-2017. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Fuel System

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems
•Relieve fuel system pressure before disconnecting fuel lines

Symptoms

•Engine cranks but does not start
•Intermittent engine stalling
•Loss of power during acceleration
•Decreased fuel efficiency
•Unusual whining noise from the fuel tank
•Check engine light illuminated

Diagnostic Steps

1
Scan for error codes using OBD-II scanner
2
Listen for fuel pump operation by turning the ignition key to 'ON'
3
Check fuel pressure with a fuel pressure gauge
4
Inspect electrical connections for corrosion or damage
5
Test fuel pump relay by swapping it with a similar relay
6
Perform a fuel pump draw test to measure current draw

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Fuel pressure gauge
•Multimeter
•Socket set
•Safety goggles

Parts Required

•Fuel pump assembly
•Fuel filter (if applicable)
•O-rings and seals

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using OBD-II scanner
2
Listen for fuel pump operation by turning the ignition key to 'ON'
3
Check fuel pressure with a fuel pressure gauge
4
Inspect electrical connections for corrosion or damage
5
Test fuel pump relay by swapping it with a similar relay
6
Perform a fuel pump draw test to measure current draw

Solution

1. Preparation

Tools Required: OBD-II scanner, fuel pressure gauge, multimeter, socket set, safety goggles.
Safety Warnings: Disconnect the battery before working on electrical systems. Relieve fuel system pressure before disconnecting fuel lines.

2. Remove the Fuel Pump

Access the Fuel Pump:
- Remove the rear seat bottom (if applicable) or access panel in the trunk to reach the fuel pump assembly.
Disconnect Electrical Connector:
- Carefully unplug the fuel pump electrical connector.
Remove Fuel Lines:
- Use a line removal tool to detach the fuel lines from the pump assembly. Be prepared for some fuel spillage, so have a rag handy.
Unscrew Pump Assembly:
- Remove the retaining ring or screws securing the fuel pump assembly to the tank and lift it out carefully.

3. Inspect and Replace

Inspect Fuel Pump:
- Check the pump for signs of wear, such as corrosion or damage.
- Use a multimeter to check the pump’s resistance; it should align with manufacturer specifications.
Replace Fuel Pump:
- If needed, install a new fuel pump by reversing the removal steps. Ensure all seals and O-rings are replaced to avoid leaks.

4. Reassemble and Test

Reattach Fuel Lines and Connector:
- Securely reconnect the fuel lines and electrical connector.
Reinstall Fuel Pump Assembly:
- Secure the pump assembly back into the tank with the retaining ring or screws.
Reconnect Battery:
- Reconnect the battery and ensure all tools are removed from the engine bay.