what causes the AC to blow warm air in my Honda Accord 9th Generation (2013-2017)

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

564 words

Problem Statement

Complete guide to fixing AC that blows warm air in Honda Accord 2013-2017. Includes symptoms, diagnostic steps, tools required, and repair procedures.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Always wear safety goggles and gloves when handling refrigerants.

Symptoms

•AC compressor is not engaging
•Warm air blowing from vents
•Unusual noises from the AC unit
•Condenser or evaporator is leaking
•Increased humidity inside the cabin

Diagnostic Steps

1
Check the AC system pressure using a manifold gauge set to determine if the refrigerant level is low.
2
Inspect the AC compressor for signs of wear or damage and ensure it is engaging when the AC is turned on.
3
Examine the fuses and relays associated with the AC system to confirm they are functioning correctly.
4
Inspect the cabin air filter for clogging that could restrict airflow.
5
Check for any visible refrigerant leaks around the AC lines and components.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Manifold gauge set
•Refrigerant (R-134a)
•Safety goggles
•Gloves
•Socket set
•Torque wrench
•AC compressor removal tool

Parts Required

•AC refrigerant
•AC compressor (if faulty)
•Cabin air filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the AC system pressure using a manifold gauge set to determine if the refrigerant level is low.
2
Inspect the AC compressor for signs of wear or damage and ensure it is engaging when the AC is turned on.
3
Examine the fuses and relays associated with the AC system to confirm they are functioning correctly.
4
Inspect the cabin air filter for clogging that could restrict airflow.
5
Check for any visible refrigerant leaks around the AC lines and components.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a flat surface.
Disconnect the negative battery terminal for safety.

2. Recharge Refrigerant

Tools Required: Manifold gauge set, refrigerant (R-134a), safety goggles, gloves
Sub-steps:
1. Connect the low-pressure side of the manifold gauge to the AC service port.
2. Start the vehicle and turn the AC to maximum cool.
3. Read the pressure on the gauge; if it is below the recommended level, proceed to recharge.
4. Attach the refrigerant can to the manifold, open the valve, and allow refrigerant to flow until the gauge indicates the correct pressure.
5. Disconnect the manifold and replace the service port cap.

3. Inspect and Replace AC Compressor

Tools Required: Socket set, torque wrench, AC compressor removal tool
Sub-steps:
1. Disconnect the electrical connector from the AC compressor.
2. Remove the serpentine belt by loosening the tensioner.
3. Remove the bolts securing the AC compressor to the engine.
4. Carefully pull the compressor out and replace it with a new unit, ensuring all seals are properly installed.
5. Torque the bolts to specification (consult repair manual for exact torque values).

4. Replace Cabin Air Filter

Tools Required: None (may require a flathead screwdriver for certain models)
Sub-steps:
1. Locate the cabin air filter access panel (usually under the glove box).
2. Remove the panel by unscrewing or unclipping it.
3. Take out the old cabin air filter and replace it with a new one.
4. Reattach the access panel securely.