why does my Honda Accord 9th Generation (2013-2017) make a clicking noise when turning

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

572 words

Problem Statement

Learn how to diagnose and fix clicking noise when turning in Honda Accord 9th Generation (2013-2017). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under the vehicle.
•Disconnect the battery before working on electrical components, if necessary.

Symptoms

•Clicking noise when turning the steering wheel
•Noise increases with speed during turns
•Vibration in the steering wheel while turning
•Possible loss of steering response
•Uneven tire wear

Diagnostic Steps

1
Inspect the CV joints for signs of wear or damage.
2
Check the power steering fluid level and inspect for leaks.
3
Examine the suspension components (control arms, bushings) for wear.
4
Inspect the wheel bearings for play or noise.
5
Perform a visual inspection of the tires for uneven wear patterns.
6
Test drive the vehicle to replicate the noise while turning.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Jack
•Jack stands
•CV joint boot clamp tool
•Grease
•OBD-II scanner
•Power steering fluid
•Pry bar
•Torque wrench

Parts Required

•CV joint assembly (if damaged)
•Power steering fluid
•Control arm bushings (if worn)
•Wheel bearing (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints for signs of wear or damage.
2
Check the power steering fluid level and inspect for leaks.
3
Examine the suspension components (control arms, bushings) for wear.
4
Inspect the wheel bearings for play or noise.
5
Perform a visual inspection of the tires for uneven wear patterns.
6
Test drive the vehicle to replicate the noise while turning.

Solution

1. Preparation

Gather tools and parts required for the repair.
Ensure the vehicle is parked on a level surface and set the parking brake.

2. Inspect and Replace CV Joints

Tools Required: Socket set, jack, jack stands, CV joint boot clamp tool, grease.
Sub-steps:
1. Raise the front of the vehicle using a jack and secure it with jack stands.
2. Remove the front wheel on the side where the noise occurs.
3. Inspect the CV joint boot for tears or leaks. If damaged, replace the CV joint assembly.
4. If the CV joint is intact, ensure it is well-lubricated; if not, clean and grease it as necessary.
5. Reinstall the wheel and lower the vehicle.

3. Check Power Steering System

Tools Required: OBD-II scanner (if checking for codes), power steering fluid.
Sub-steps:
1. Check the power steering fluid level; add fluid if low.
2. Inspect for leaks in hoses and connection points.
3. If leaks are found, replace the affected hoses or components.

4. Inspect Suspension Components

Tools Required: Socket set, pry bar.
Sub-steps:
1. With the vehicle still raised, visually inspect the control arms and bushings for any signs of wear or damage.
2. Use a pry bar to check for play in the bushings.
3. Replace any worn-out bushings or components.

5. Inspect Wheel Bearings

Tools Required: Torque wrench, socket set.
Sub-steps:
1. Spin the wheel by hand to check for any grinding noises.
2. If noise is present, the wheel bearing may need replacement.
3. Remove the wheel, brake caliper, and rotor to access the bearing.
4. Replace the bearing, ensuring proper torque specifications are followed for reinstallation.