why does my Honda Accord 9th Generation (2013-2017) transmission slip when accelerating

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

528 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission slipping in Honda Accord 9th Generation (2013-2017). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the transmission to avoid burns.

Symptoms

•Loss of power during acceleration
•High RPMs without corresponding vehicle speed increase
•Delayed engagement when shifting from park to drive
•Warning light illuminated on the dashboard
•Fluid leaks under the vehicle
•Unusual noises from the transmission

Diagnostic Steps

1
Scan the vehicle’s computer for any transmission-related error codes using an OBD-II scanner.
2
Check the transmission fluid level and condition (color and smell).
3
Inspect the transmission for any visible leaks or damage to seals and gaskets.
4
Examine the transmission filter for clogs or restrictions.
5
Test the transmission solenoids for proper operation using a multimeter.
6
Perform a road test to replicate slipping and note the conditions (speed, temperature).

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Multimeter
•Transmission fluid pump

Parts Required

•Honda ATF DW-1 transmission fluid
•Transmission filter
•Gasket for transmission pan
•Transmission solenoids

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle’s computer for any transmission-related error codes using an OBD-II scanner.
2
Check the transmission fluid level and condition (color and smell).
3
Inspect the transmission for any visible leaks or damage to seals and gaskets.
4
Examine the transmission filter for clogs or restrictions.
5
Test the transmission solenoids for proper operation using a multimeter.
6
Perform a road test to replicate slipping and note the conditions (speed, temperature).

Solution

1. Preparation

Ensure the vehicle is parked on a level surface and the engine is cool.
Gather all necessary tools and parts.
Disconnect the battery to prevent any electrical issues.

2. Check and Replace Transmission Fluid

Sub-steps:
1. Remove the transmission dipstick and check fluid level.
2. If low, add the recommended transmission fluid (Honda ATF DW-1).
3. If fluid is dark or burnt, drain the old fluid from the transmission pan.
4. Remove the transmission pan bolts using a socket set and gently lower the pan.
5. Replace the transmission filter as needed.
6. Clean the pan and replace the gasket before reinstallation.
7. Refill the transmission with new fluid through the dipstick tube.

3. Inspect and Replace Transmission Solenoids

Sub-steps:
1. Remove the transmission pan again if it’s not already off.
2. Locate the transmission solenoids and disconnect the electrical connectors.
3. Remove any retaining bolts and take out the solenoids.
4. Install new solenoids by reversing the removal process.
5. Reinstall the transmission pan and refit all components.

4. Reconnect Battery and Test

Reconnect the battery terminals.
Start the engine and allow it to reach operating temperature.
Perform a test drive to confirm that the slipping issue has been resolved.