why is my Honda Accord 9th Generation (2013-2017) engine light on after oil change?

Honda Accord Eleventh Generation (2023-present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

498 words

Problem Statement

Learn why the check engine light may illuminate after an oil change in your Honda Accord 2013-2017. Follow our diagnostic steps and solutions.

Affected Component

Engine

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Ensure the engine is cool to avoid burns.
•Use caution as the filter may be hot.
•Make sure to follow the proper sequence as per the owner's manual.
•Ensure the engine is off before inspecting the hoses.

Symptoms

•Check engine light illuminated
•Oil change light remains on
•Possible engine performance issues (e.g., rough idle)
•Unusual oil consumption
•Oil leakage under the vehicle

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific issues.
2
Verify that the correct oil type and viscosity were used.
3
Check the oil filter for proper installation and any leaks.
4
Inspect for any loose or disconnected hoses that may have been disturbed during the oil change.
5
Reset the oil change light in the vehicle's system if it has not been reset.
6
Examine the engine for any signs of oil leaks or drips.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Oil dipstick
•Oil filter wrench
•Basic hand tools (screwdriver, pliers)

Parts Required

•Oil filter (if needed)
•Engine oil (if low)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific issues.
2
Verify that the correct oil type and viscosity were used.
3
Check the oil filter for proper installation and any leaks.
4
Inspect for any loose or disconnected hoses that may have been disturbed during the oil change.
5
Reset the oil change light in the vehicle's system if it has not been reset.
6
Examine the engine for any signs of oil leaks or drips.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface.
Disconnect the battery for safety if working on electrical components.

2. Check Oil Quality and Level

Remove the dipstick and wipe it clean.
Reinsert the dipstick, then remove it again to check the oil level and quality.
- Tools Required: Oil dipstick
- Safety Warnings: Ensure the engine is cool to avoid burns.

3. Inspect Oil Filter

Locate the oil filter and check it for proper installation.
If loose, tighten it; if damaged, replace it.
- Tools Required: Oil filter wrench
- Safety Warnings: Use caution as the filter may be hot.

4. Reset the Oil Change Light

Turn the ignition to the "ON" position without starting the engine.
Press the gas pedal three times in quick succession to reset the oil change light.
- Tools Required: None
- Safety Warnings: Make sure to follow the proper sequence as per the owner's manual.

5. Inspect for Air Leaks

Visually inspect hoses and connections around the intake for any disconnections or cracks.
Replace any damaged hoses.
- Tools Required: Basic hand tools (screwdriver, pliers)
- Safety Warnings: Ensure the engine is off before inspecting the hoses.