how to troubleshoot Honda Accord 10th Generation (2018-2022) transmission jerking issues

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

562 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to troubleshoot and fix transmission jerking issues in Honda Accord 10th Generation (2018-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before inspecting the transmission fluid.

Symptoms

•Transmission jerking during acceleration
•Delayed or harsh shifting between gears
•RPM fluctuations while driving
•Engine revs without corresponding vehicle acceleration
•"Transmission" warning light illuminated on the dashboard

Diagnostic Steps

1
Scan the vehicle’s onboard diagnostics (OBD-II) for any error codes related to the transmission.
2
Check the transmission fluid level and condition; look for signs of contamination or burning.
3
Inspect the transmission control module (TCM) for any visible damage or loose connections.
4
Test the throttle position sensor (TPS) for proper functionality using a multimeter.
5
Evaluate the engine and transmission mounts for wear or damage that could cause jerking.
6
Perform a road test to observe the transmission behavior under different driving conditions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Multimeter
•Transmission fluid pump

Parts Required

•Honda ATF DW-1 transmission fluid
•Transmission filter (if applicable)
•Throttle position sensor (if faulty)
•Transmission/engine mounts (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle’s onboard diagnostics (OBD-II) for any error codes related to the transmission.
2
Check the transmission fluid level and condition; look for signs of contamination or burning.
3
Inspect the transmission control module (TCM) for any visible damage or loose connections.
4
Test the throttle position sensor (TPS) for proper functionality using a multimeter.
5
Evaluate the engine and transmission mounts for wear or damage that could cause jerking.
6
Perform a road test to observe the transmission behavior under different driving conditions.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a level surface, and set the parking brake.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Check and Replace Transmission Fluid

Sub-steps:
1. Locate the transmission dipstick and remove it.
2. Check the fluid level; add fluid if necessary.
3. If the fluid is dark or has a burnt smell, drain the old fluid.
4. Use a wrench to remove the transmission pan bolts and carefully lower the pan.
5. Replace the transmission filter if applicable.
6. Reinstall the transmission pan with a new gasket and torque the bolts to the manufacturer’s specifications (typically around 8-10 ft-lbs).
7. Fill with new transmission fluid (Honda ATF DW-1) as specified in the owner’s manual.

3. Inspect and Repair Transmission Control Module (TCM)

Sub-steps:
1. Remove the TCM from its mounting location.
2. Inspect the wiring harness for damage; repair or replace as necessary.
3. Reinstall the TCM and ensure all connections are secure.

4. Test and Replace Throttle Position Sensor (if faulty)

Sub-steps:
1. Disconnect the electrical connector from the TPS.
2. Using a multimeter, check the voltage output of the TPS while moving the throttle.
3. If the readings are not within manufacturer specifications, replace the TPS.
4. Reconnect the new TPS and clear any diagnostic codes.

5. Inspect and Replace Engine/Transmission Mounts

Sub-steps:
1. Visually inspect the mounts for cracks or separation.
2. If damaged, remove the old mounts using a socket set.
3. Install new mounts and torque to manufacturer specifications.