my Honda Accord 10th Generation (2018-2022) has a loud humming noise, could it be the wheel bearing?

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

544 words

Problem Statement

Learn how to diagnose and fix loud humming noise in Honda Accord 10th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is securely lifted and supported before working underneath.
•Wear safety glasses to protect against debris when removing components.

Symptoms

•Loud humming noise while driving
•Noise increases with vehicle speed
•Vibration felt in the steering wheel or floorboard
•Uneven tire wear visible on inspection
•Possible pulling to one side while driving

Diagnostic Steps

1
Conduct a visual inspection of the tires for uneven wear patterns.
2
Lift the vehicle using a jack and secure it with jack stands.
3
Rotate each wheel by hand to listen for noise or roughness.
4
Check for play in the wheel by grabbing the top and bottom of the tire and rocking it.
5
Use an OBD-II scanner to check for any related error codes, although they might not directly indicate wheel bearing issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Lug wrench
•Jack and jack stands
•Bearing puller
•Torque wrench
•OBD-II scanner

Parts Required

•New wheel bearing
•Brake caliper hardware (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Conduct a visual inspection of the tires for uneven wear patterns.
2
Lift the vehicle using a jack and secure it with jack stands.
3
Rotate each wheel by hand to listen for noise or roughness.
4
Check for play in the wheel by grabbing the top and bottom of the tire and rocking it.
5
Use an OBD-II scanner to check for any related error codes, although they might not directly indicate wheel bearing issues.

Solution

1. Preparation

Gather tools and parts required.
Park the vehicle on a flat surface and engage the parking brake.
Disconnect the negative battery terminal to ensure safety.

2. Lift the Vehicle

Use a jack to lift the front or rear of the vehicle, depending on which wheel bearing is suspected.
Secure the vehicle with jack stands before proceeding.

3. Remove Wheel

Use a lug wrench to loosen and remove the lug nuts.
Take off the wheel to access the brake assembly and wheel bearing.

4. Inspect and Replace Wheel Bearing

Inspection:
- Visually inspect the wheel bearing for signs of damage or wear.
- Check for grease leakage around the bearing area.
Replacement:
- Remove the brake caliper and rotor to access the wheel hub.
- Remove the retaining bolt or circlip holding the wheel bearing in place.
- Use a bearing puller to extract the old wheel bearing from the hub.
- Clean the hub area and install the new wheel bearing using a press, ensuring proper alignment.
- Reinstall the retaining bolt or circlip to secure the bearing.

5. Reassemble Components

Reattach the brake rotor and caliper.
Place the wheel back on and hand-tighten the lug nuts.
Lower the vehicle to the ground and torque the lug nuts to manufacturer specifications (typically around 80-100 lb-ft).

6. Final Check

Reconnect the negative battery terminal.
Start the vehicle and test drive to ensure the noise has been eliminated.