my Honda Accord 10th Generation (2018-2022) has a ticking noise when I accelerate, what's causing it...

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

546 words

Problem Statement

Learn how to diagnose and fix a ticking noise during acceleration in Honda Accord 10th Generation (2018-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool down before opening the oil filler cap or drain plug.

Symptoms

•Ticking noise increases with acceleration
•Noise is more pronounced during engine load
•Possible loss of power
•Engine vibrations felt through the vehicle
•Check engine light may illuminate

Diagnostic Steps

1
Inspect the engine oil level and condition to rule out insufficient lubrication.
2
Listen for the noise from different areas of the engine bay to localize the source.
3
Use an OBD-II scanner to check for any stored error codes related to engine function.
4
Examine the exhaust system for leaks or loose components that may cause ticking sounds.
5
Inspect the drive belts and pulleys for wear or damage.
6
Check for any loose or damaged components in the engine bay, including heat shields.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Oil filter wrench
•Torque wrench
•Socket set
•Oil drain pan
•Funnel

Parts Required

•Engine oil (0W-20)
•Oil filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the engine oil level and condition to rule out insufficient lubrication.
2
Listen for the noise from different areas of the engine bay to localize the source.
3
Use an OBD-II scanner to check for any stored error codes related to engine function.
4
Examine the exhaust system for leaks or loose components that may cause ticking sounds.
5
Inspect the drive belts and pulleys for wear or damage.
6
Check for any loose or damaged components in the engine bay, including heat shields.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the battery to ensure safety while working on the vehicle.

2. Inspect and Change Engine Oil

Sub-steps:
1. Remove the oil dipstick and check the oil level; add oil if low.
2. If oil is dirty or has not been changed in a while, drain the engine oil using a wrench to remove the oil pan plug.
3. Replace the oil filter using an oil filter wrench.
4. Refill the engine with the recommended oil type (usually 0W-20 for Honda).
Tools Required: Oil filter wrench, socket set, oil drain pan, funnel.

3. Tighten Loose Components

Sub-steps:
1. Inspect all visible bolts and fasteners in the engine bay, especially around the engine mounts and exhaust manifold.
2. Use a torque wrench to tighten any loose bolts to the specified torque values.
Tools Required: Torque wrench, socket set.

4. Repair or Replace Faulty Components

Sub-steps:
1. If a specific component, such as a pulley or the exhaust system, is found to be loose or damaged, replace it with a new part.
2. If the noise is from the valve train, consider adjusting or replacing the valve lifters or timing components if necessary.
Tools Required: Depending on the component, you may need various hand tools and potentially a timing tool set if working on internal engine components.