my Honda Accord 10th Generation (2018-2022) makes a knocking noise when accelerating

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

4 min read

612 words

Problem Statement

Learn how to diagnose and fix knocking noise during acceleration in Honda Accord 10th Generation (2018-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before starting any work on electrical systems.
•Ensure the engine is cool before performing any inspections.

Symptoms

•Knocking noise during acceleration
•Possible loss of power
•Vibration felt in the cabin
•Engine stalling intermittently
•Check engine light may be illuminated
•Increased fuel consumption

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the engine oil level and condition to ensure proper lubrication.
3
Check for any loose or damaged engine mounts that may contribute to noise during acceleration.
4
Examine the exhaust system for any leaks or loose components that could create knocking sounds.
5
Inspect the drive shaft and CV joints for any signs of wear or damage.
6
Conduct a visual inspection of the intake system for any loose components or debris that may cause noise.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Jack and jack stands
•Screwdrivers

Parts Required

•Engine oil (0W-20)
•Oil filter
•Engine mount (if needed)
•Exhaust components (if needed)
•CV joint (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the engine oil level and condition to ensure proper lubrication.
3
Check for any loose or damaged engine mounts that may contribute to noise during acceleration.
4
Examine the exhaust system for any leaks or loose components that could create knocking sounds.
5
Inspect the drive shaft and CV joints for any signs of wear or damage.
6
Conduct a visual inspection of the intake system for any loose components or debris that may cause noise.

Solution

1. Preparation

Gather tools and parts required for the repairs.
Tools Required:
- OBD-II scanner
- Socket set
- Torque wrench
- Jack and jack stands
- Screwdrivers
Safety Warnings:
- Disconnect the battery before starting any work on electrical systems.
- Ensure the engine is cool before performing any inspections.

2. Address Engine Oil Issues

Check the oil level using the dipstick.
If low, top off with the manufacturer's recommended oil type (e.g., 0W-20).
If the oil is dirty, change the oil and oil filter:
1. Drain the old oil into a pan.
2. Replace the oil filter using an oil filter wrench.
3. Refill with new oil, ensuring to replace the oil cap.

3. Inspect and Replace Engine Mounts (if damaged)

Raise the vehicle using a jack and secure with jack stands.
Visually inspect the engine mounts for cracks or separation.
If damaged:
1. Remove the bolts securing the engine mount to the engine and frame.
2. Install the new engine mount and torque bolts to manufacturer specifications (typically 40-50 ft-lbs).
3. Lower the vehicle and test for noise.

4. Check and Repair Exhaust System

Inspect the exhaust for loose connections or holes.
Tighten any loose bolts or clamps.
If any part is damaged, replace the affected section:
1. Cut the section with a pipe cutter.
2. Install a new exhaust pipe with clamps and ensure a secure fit.

5. Inspect Drive Shaft and CV Joints

Examine the drive shaft for any signs of wear or damage.
Check CV joints for torn boots or excessive play.
If damaged, replace the affected joint:
1. Remove the wheel and brake assembly.
2. Disconnect the CV joint from the drive shaft.
3. Install the new CV joint and reassemble.