my Honda Accord 8th Generation (2008-2012) shakes while braking what should I check

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

531 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix brake shaking in Honda Accord 2008-2012. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on the braking system.
•Allow the vehicle to cool before touching brake components after use.

Symptoms

•Steering wheel shakes during braking
•Vibration felt in the brake pedal
•Uneven wear on brake pads or rotors
•Potential noise (squealing or grinding) when braking
•Decreased braking performance or increased stopping distance

Diagnostic Steps

1
Inspect brake rotors for warping by measuring thickness at multiple points.
2
Check brake pads for uneven wear or glazing.
3
Verify caliper operation to ensure they are not sticking or seizing.
4
Examine suspension components (e.g., tie rods, control arms, wheel bearings) for wear or damage.
5
Inspect tire condition and pressure to rule out tire-related issues.
6
Check wheel alignment and balance.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Brake cleaner
•Jack
•Jack stands

Parts Required

•New brake rotors
•New brake pads

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake rotors for warping by measuring thickness at multiple points.
2
Check brake pads for uneven wear or glazing.
3
Verify caliper operation to ensure they are not sticking or seizing.
4
Examine suspension components (e.g., tie rods, control arms, wheel bearings) for wear or damage.
5
Inspect tire condition and pressure to rule out tire-related issues.
6
Check wheel alignment and balance.

Solution

1. Preparation

Gather tools: socket set, torque wrench, brake cleaner, and a jack.
Ensure the vehicle is on a flat surface and engage the parking brake.
Wear appropriate safety gear (gloves and goggles).

2. Lift the Vehicle

Use a jack to lift the front or rear of the vehicle, depending on which brakes are affected.
Secure with jack stands to ensure safety while working.

3. Remove Wheel

Using a socket wrench, remove the lug nuts and take off the wheel to access the braking components.

4. Inspect and Replace Brake Rotors

Inspection: Check the rotors for warping using a dial indicator or caliper.
Replacement:
1. If warped, remove the caliper by unscrewing the caliper bolts.
2. Slide the caliper off the rotor and support it to avoid stress on the brake line.
3. Remove the old rotor by unscrewing any retaining screws.
4. Install the new rotor, ensuring it is seated properly.
5. Reattach the caliper and torque the bolts to manufacturer specifications.

5. Inspect and Replace Brake Pads

Inspection: Assess the brake pads for wear. Replace if they are below the manufacturer's minimum thickness.
Replacement:
1. Remove the old brake pads by sliding them out of the caliper bracket.
2. Clean the caliper bracket and apply brake grease to contact points.
3. Install new pads ensuring they are correctly oriented.
4. Reassemble the caliper and torque the bolts.

6. Reassemble and Lower the Vehicle

Reattach the wheel and hand-tighten the lug nuts.
Lower the vehicle and then torque the lug nuts to the manufacturer’s specifications.