what does it mean if my Honda Accord 8th Generation (2008-2012) has engine codes P0134 and P0135

Honda Accord 8th Generation (2008-2012)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

Error Code: P0134, P0135

3 min read

525 words

Problem Statement

Learn how to diagnose and fix P0134 and P0135 oxygen sensor issues in Honda Accord 2008-2012. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0134, P0135

Affected Component

Exhaust System

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the exhaust system.

Symptoms

•Check engine light illuminated
•Poor fuel economy
•Rough idle or stalling
•Increased emissions
•Sluggish acceleration

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics using an OBD-II scanner to confirm the presence of codes P0134 and P0135.
2
Inspect the oxygen sensor wiring and connectors for damage, corrosion, or loose connections.
3
Measure the voltage output of the oxygen sensor while the engine is running to determine if it is functioning correctly.
4
Check the fuse related to the oxygen sensor heater circuit for continuity.
5
Test the oxygen sensor heater circuit with a multimeter to ensure it is receiving the correct voltage.
6
Inspect the exhaust system for leaks that could affect the readings of the oxygen sensor.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket wrench and oxygen sensor socket
•Multimeter
•Torque wrench

Parts Required

•Oxygen sensor (front)
•Fuses (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics using an OBD-II scanner to confirm the presence of codes P0134 and P0135.
2
Inspect the oxygen sensor wiring and connectors for damage, corrosion, or loose connections.
3
Measure the voltage output of the oxygen sensor while the engine is running to determine if it is functioning correctly.
4
Check the fuse related to the oxygen sensor heater circuit for continuity.
5
Test the oxygen sensor heater circuit with a multimeter to ensure it is receiving the correct voltage.
6
Inspect the exhaust system for leaks that could affect the readings of the oxygen sensor.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the negative battery terminal to prevent electrical shorts.
Allow the engine to cool before starting work.

2. Remove the Oxygen Sensor

Locate the front oxygen sensor (typically near the exhaust manifold).
Use a socket wrench to carefully unscrew the oxygen sensor.
Disconnect the electrical connector by pressing the release tab and pulling it apart.

3. Inspect and Replace the Oxygen Sensor

Inspect the old oxygen sensor for signs of wear or damage.
If the sensor is faulty, install a new oxygen sensor.
- Ensure it's compatible with the 2008-2012 Honda Accord.
- Apply anti-seize compound to the threads of the new sensor (if recommended).
Screw in the new sensor by hand and then tighten it with the socket wrench to the manufacturer's specified torque (usually around 30 lb-ft).

4. Reconnect Electrical Connectors

Reattach the electrical connector to the new oxygen sensor.
Ensure the connector is secure and free of corrosion.

5. Check Heater Circuit

If P0135 persists after replacing the sensor, check the oxygen sensor heater circuit.
Replace any blown fuses related to the oxygen sensor heater circuit.
If issues remain, inspect the wiring for breaks or shorts.

6. Reconnect Battery and Reset Codes

Reconnect the negative battery terminal.
Use the OBD-II scanner to clear the error codes.
Start the engine and allow it to reach operating temperature.