why does my Honda Accord 10th Generation (2018-2022) make a grinding noise when I drive

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

588 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix grinding noise issues in Honda Accord 10th Generation (2018-2022). Step-by-step guide with symptoms, diagnostics, and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the vehicle to cool down before touching any components post-drive.

Symptoms

•Grinding noise when the vehicle is in motion
•Noise increases with speed
•Potential vibrations felt through the steering wheel or floor
•Decreased braking performance (if noise is related to brakes)
•Unusual wear patterns on tires (if related to bearings or alignment)

Diagnostic Steps

1
Inspect the brake pads and rotors for wear or damage.
2
Check for any debris lodged between the brake components.
3
Lift the vehicle and manually spin each wheel to listen for grinding noises from bearings.
4
Inspect wheel bearings for play or excessive wear.
5
Perform a visual inspection of the drivetrain components (CV joints, axles) for signs of damage or wear.
6
Check the tire condition and alignment.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Brake cleaner
•C-clamp (for caliper piston compression)
•Bearing press (if replacing wheel bearings)

Parts Required

•Brake pads
•Brake rotors (if necessary)
•Wheel bearings (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the brake pads and rotors for wear or damage.
2
Check for any debris lodged between the brake components.
3
Lift the vehicle and manually spin each wheel to listen for grinding noises from bearings.
4
Inspect wheel bearings for play or excessive wear.
5
Perform a visual inspection of the drivetrain components (CV joints, axles) for signs of damage or wear.
6
Check the tire condition and alignment.

Solution

1. Preparation

Gather all necessary tools and replacement parts.
Ensure the vehicle is parked on a level surface and engage the parking brake.
Disconnect the battery for safety during brake and electrical component inspection.

2. Inspect and Replace Brake Components

Remove the Wheel
- Use a jack to lift the vehicle and secure it with jack stands.
- Remove the lug nuts using a socket wrench and take off the wheel.
Inspect Brake Pads and Rotors
- Check brake pads for thickness; replace if less than 3mm.
- Inspect the rotors for scoring or warping; replace if damaged.
- Use a brake cleaner to clean the rotor surface if reusing.
Replace Brake Pads and Rotors (if necessary)
- Remove the caliper bolts and slide the caliper off the rotor.
- Replace the pads by compressing the caliper piston using a C-clamp.
- Install the new rotor and caliper, tightening bolts to manufacturer’s specifications (typically, around 25-30 ft-lbs).

3. Inspect and Replace Wheel Bearings (if necessary)

Remove the Wheel Hub
- If bearings are damaged, disconnect the brake caliper and rotor.
- Remove the axle nut and any retaining bolts for the wheel hub.
- Pull the hub assembly off the steering knuckle.
Replace the Wheel Bearings
- Use a bearing press to remove the old bearings from the hub.
- Install new bearings using the press, ensuring proper alignment.
- Reassemble the hub and ensure all bolts are torqued to specifications.

4. Reassemble and Test

Reinstall the wheel and lug nuts, tightening them to the manufacturer’s torque specs (typically 80-100 ft-lbs).
Lower the vehicle and reconnect the battery.
Perform a test drive to ensure the grinding noise is eliminated.