why is my Honda Accord 10th Generation (2018-2022) making a knocking noise

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

537 words

Problem Statement

Diagnose and fix knocking noise in Honda Accord 10th Generation (2018-2022). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components
•Allow the engine to cool before inspecting

Symptoms

•Knocking noise during acceleration or deceleration
•Noise occurs over bumps or rough surfaces
•Possible engine misfire or rough running
•Loss of power or reduced acceleration
•Vibration felt in the steering wheel or floorboard

Diagnostic Steps

1
Inspect for external sources of noise in the engine bay or undercarriage
2
Scan for error codes using an OBD-II scanner
3
Check engine oil level and condition
4
Examine suspension components for wear or damage
5
Listen for noise location using a mechanic's stethoscope
6
Test drive the vehicle under various conditions to replicate the noise

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Mechanic's stethoscope
•Basic hand tools (sockets, wrenches)
•Jack and jack stands
•Torque wrench

Parts Required

•Engine mounts (if damaged)
•Timing chain/belt (if worn)
•Shock absorbers/struts (if leaking)
•Control arms/bushings (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect for external sources of noise in the engine bay or undercarriage
2
Scan for error codes using an OBD-II scanner
3
Check engine oil level and condition
4
Examine suspension components for wear or damage
5
Listen for noise location using a mechanic's stethoscope
6
Test drive the vehicle under various conditions to replicate the noise

Solution

1. Preparation

Tools Needed: OBD-II scanner, mechanic's stethoscope, basic hand tools (sockets, wrenches).
Safety Warnings: Disconnect the battery before working on electrical components; allow the engine to cool before inspecting.

2. Inspect Engine Components

Check Engine Mounts:
- Use a socket set to inspect and tighten any loose bolts on the engine mounts.
- Replace any damaged mounts with OEM parts if necessary.
Examine Timing Chain/Belt:
- Remove the engine cover (if applicable) using a socket set.
- Inspect for wear or damage; replace if necessary. Ensure proper tension and alignment are maintained.

3. Inspect Suspension System

Check Shock Absorbers and Struts:
- Raise the vehicle using a jack and secure it with jack stands.
- Inspect shock absorbers and struts for leaks or physical damage.
- Replace any defective units with OEM replacements.
Inspect Control Arms and Bushings:
- Check for any excessive play in control arms and bushings.
- Replace worn bushings and control arms as needed.

4. Check Engine Oil

Remove the oil dipstick and check the oil level and condition.
If low, top off with the manufacturer-recommended oil type. If dirty, consider performing an oil change.