why is my Honda Accord using too much oil?

Honda Accord 9th Generation (2013-2017)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

544 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix excessive oil consumption in Honda Accord. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow engine to cool before opening any components.
•Use gloves and safety goggles when handling oil and cleaning agents.

Symptoms

•Check engine light illuminated
•Oil level dropping significantly between oil changes
•Blue smoke from the exhaust
•Engine misfires or reduced performance
•Unusual engine noise (ticking or knocking)
•Increased oil pressure

Diagnostic Steps

1
Check for diagnostic trouble codes (DTCs) using an OBD-II scanner.
2
Inspect the engine for visible oil leaks around gaskets and seals.
3
Perform a compression test on each cylinder to identify potential internal leaks.
4
Check the condition of the PCV (Positive Crankcase Ventilation) valve for proper operation.
5
Inspect the oil filter for signs of contamination or blockage.
6
Analyze the engine oil for signs of fuel dilution or contamination.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Compression tester
•Oil filter wrench
•Oil catch pan

Parts Required

•Valve cover gasket
•Oil pan gasket
•PCV valve
•Engine oil
•Oil filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check for diagnostic trouble codes (DTCs) using an OBD-II scanner.
2
Inspect the engine for visible oil leaks around gaskets and seals.
3
Perform a compression test on each cylinder to identify potential internal leaks.
4
Check the condition of the PCV (Positive Crankcase Ventilation) valve for proper operation.
5
Inspect the oil filter for signs of contamination or blockage.
6
Analyze the engine oil for signs of fuel dilution or contamination.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Allow the engine to cool down to avoid burns.

2. Address Oil Leaks

Sub-steps:
1. Use a socket set to remove any engine covers if necessary.
2. Clean the engine area with a degreaser to identify leaks.
3. Replace any faulty gaskets or seals (valve cover gasket, oil pan gasket) as needed, ensuring to apply the correct torque specifications.

3. Replace the PCV Valve

Sub-steps:
1. Locate the PCV valve (typically found on the valve cover).
2. Disconnect the hose connected to the PCV valve.
3. Twist and pull to remove the old PCV valve.
4. Install the new PCV valve and reconnect the hose securely.

4. Perform Engine Compression Test

Sub-steps:
1. Remove the spark plugs using a socket wrench.
2. Insert the compression tester into the spark plug hole.
3. Crank the engine and record the compression readings for each cylinder.
4. Compare readings; if any cylinder is significantly lower, further investigation into piston rings or cylinder walls may be necessary.

5. Oil Change

Sub-steps:
1. Drain the old engine oil by removing the oil drain plug with a wrench.
2. Replace the oil filter using an oil filter wrench.
3. Fill the engine with the manufacturer-recommended oil type and capacity.
4. Recheck the oil level after starting the engine and let it run for a few minutes.

Tools Required:

OBD-II scanner
Socket set
Torque wrench
Compression tester
Oil filter wrench
Oil catch pan

Parts Required:

Valve cover gasket
Oil pan gasket
PCV valve
Engine oil
Oil filter

Estimated Repair Time: 2-4 hours

Safety Warnings:

Disconnect the battery before working on electrical systems.
Allow engine to cool before opening any components.
Use gloves and safety goggles when handling oil and cleaning agents.