how to resolve the P0135 code on my Honda Civic 10th Generation (2016-2021)?

Honda Civic 10th Generation (2016-2021)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

Error Code: P0135

3 min read

539 words

Problem Statement

Learn how to diagnose and fix P0135 oxygen sensor heater circuit issues in Honda Civic 10th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0135

Affected Component

Exhaust System

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working near the exhaust system.

Symptoms

•Check engine light illuminated
•Decreased fuel efficiency
•Rough idle or stalling
•Poor acceleration or power loss
•Increased emissions during inspection

Diagnostic Steps

1
Scan the vehicle's onboard computer with an OBD-II scanner to confirm P0135 and check for any additional codes.
2
Inspect the wiring and connectors of the oxygen sensor for any signs of damage, corrosion, or loose connections.
3
Use a multimeter to measure the resistance of the oxygen sensor heater circuit; compare readings to specifications.
4
Check the fuse related to the oxygen sensor heater circuit to ensure it is intact.
5
Perform a visual inspection of the oxygen sensor itself to ensure it is not clogged or damaged.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•O2 sensor socket
•Torque wrench
•Wire brush

Parts Required

•New oxygen sensor
•Fuse (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's onboard computer with an OBD-II scanner to confirm P0135 and check for any additional codes.
2
Inspect the wiring and connectors of the oxygen sensor for any signs of damage, corrosion, or loose connections.
3
Use a multimeter to measure the resistance of the oxygen sensor heater circuit; compare readings to specifications.
4
Check the fuse related to the oxygen sensor heater circuit to ensure it is intact.
5
Perform a visual inspection of the oxygen sensor itself to ensure it is not clogged or damaged.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is parked on a flat surface, and the engine is cool.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Replace the Oxygen Sensor

Tools Required: Socket set, O2 sensor socket, Torque wrench, Wire brush (for cleaning connectors), Multimeter
Locate the oxygen sensor (usually on the exhaust manifold or downstream).
Disconnect the wiring harness from the oxygen sensor.
Use the O2 sensor socket to unscrew the old sensor from its mounting location.
Clean the threads of the mounting hole with a wire brush to remove debris and carbon deposits.
Apply a small amount of anti-seize compound to the threads of the new oxygen sensor (if recommended).
Screw in the new oxygen sensor by hand to avoid cross-threading, then use a torque wrench to tighten to manufacturer specifications (typically around 30-40 ft-lbs, refer to the specific service manual).
Reconnect the wiring harness securely.

3. Check Connections and Fuses

Tools Required: Multimeter
Inspect the wiring harness and connectors for any signs of damage; repair or replace as necessary.
Check the fuse related to the oxygen sensor heater circuit by using a multimeter or visually inspecting it. Replace if blown.

4. Reconnect Battery and Clear Codes

Reconnect the negative battery terminal.
Use the OBD-II scanner to clear the P0135 code from the vehicle's computer.