what to do if my Honda Civic 9th Generation (2012-2015) AC is not blowing cold

Honda Civic 9th Generation (2012-2015)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

541 words

Problem Statement

Learn how to diagnose and fix AC not blowing cold in Honda Civic 9th Generation (2012-2015). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Use caution when handling refrigerants; follow proper disposal and handling procedures.

Symptoms

•AC system blowing warm air
•Increased cabin humidity
•Unusual noises from the AC compressor
•AC compressor not engaging
•"Check AC" warning light illuminated on the dashboard

Diagnostic Steps

1
Check the AC system's refrigerant level using a gauge set.
2
Inspect the AC compressor for any visible signs of damage or leaks.
3
Verify that the AC compressor clutch is engaging by observing its operation when the AC is turned on.
4
Scan the vehicle's OBD-II system for any error codes related to the AC system.
5
Inspect the AC condenser for obstructions or debris that could impede airflow.
6
Check the cabin air filter for clogging or restrictions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Safety glasses
•Gloves
•AC manifold gauge set
•Refrigerant
•Socket set

Parts Required

•AC compressor (if replacement is needed)
•Cabin air filter (if replacement is needed)
•AC refrigerant

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the AC system's refrigerant level using a gauge set.
2
Inspect the AC compressor for any visible signs of damage or leaks.
3
Verify that the AC compressor clutch is engaging by observing its operation when the AC is turned on.
4
Scan the vehicle's OBD-II system for any error codes related to the AC system.
5
Inspect the AC condenser for obstructions or debris that could impede airflow.
6
Check the cabin air filter for clogging or restrictions.

Solution

1. Preparation

Tools Required: Safety glasses, gloves, AC manifold gauge set, refrigerant.
Ensure the vehicle is parked in a well-ventilated area.
Disconnect the battery to prevent electrical shock.

2. Recharge the AC System

Sub-steps:
1. Connect the low-pressure side of the AC manifold gauge to the low-pressure service port.
2. Start the engine and turn the AC to the maximum setting.
3. Check the pressure reading; if it's low, add refrigerant according to the manufacturer’s specifications (R-134a for Honda Civic).
4. Monitor the pressure gauge while adding refrigerant to avoid overcharging.

3. Inspect and Replace AC Compressor

Sub-steps:
1. If the compressor is not engaging, check the electrical connections and fuses.
2. If faulty, remove the serpentine belt by loosening the tensioner.
3. Disconnect the AC lines from the compressor and remove the mounting bolts.
4. Install the new compressor and reconnect the AC lines.
5. Reinstall the serpentine belt and tension it properly.

4. Clean or Replace Cabin Air Filter

Sub-steps:
1. Locate the cabin air filter compartment, typically under the dashboard or behind the glove box.
2. Remove the filter cover and take out the old filter.
3. Inspect the new filter for correct orientation and install it securely.
4. Reattach the cover and ensure it is secured.