how to replace brake pads on Honda CR-V Fifth Generation (2017-2022)

Honda CR-V Fifth Generation (2017-2022)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

3 min read

596 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to replace brake pads on a 2017-2022 Honda CR-V. Step-by-step guide with symptoms, diagnostic steps, tools, and safety tips.

Affected Component

Brakes

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always wear safety glasses when working on brakes.
•Ensure the vehicle is securely lifted and supported before working underneath.

Symptoms

•Squeaking or squealing noise when braking
•Grinding noise indicating metal-to-metal contact
•Reduced braking efficiency or longer stopping distance
•Vibration or pulsation in the brake pedal
•Brake warning light illuminated on the dashboard

Diagnostic Steps

1
Inspect the brake pads visually for wear indicators.
2
Check the brake rotor surface for grooves or scoring.
3
Measure the thickness of the brake pads using a caliper.
4
Confirm brake fluid level and condition in the master cylinder.
5
Test brake performance by applying brakes at low speeds.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Lug wrench
•Socket set
•Torque wrench
•C-clamp or brake caliper tool
•Brake cleaner
•Safety glasses

Parts Required

•New brake pads
•Brake grease

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Tools Required: Jack, jack stands, lug wrench, socket set, torque wrench, C-clamp or brake caliper tool, brake cleaner, and safety glasses.
Park the vehicle on a level surface and engage the parking brake.
Use the lug wrench to loosen the lug nuts slightly while the vehicle is still on the ground.

2. Lift the Vehicle

Use the jack to lift the front or rear of the vehicle (depending on which brake pads are being replaced).
Secure the vehicle with jack stands.
Remove the lug nuts completely and take off the wheel.

3. Remove Brake Caliper

Locate the caliper mounting bolts (usually two bolts).
Use a socket to remove the caliper bolts.
Carefully slide the caliper off the brake rotor. Do not disconnect the brake line; instead, support the caliper using a bungee cord or similar tool.

4. Remove Old Brake Pads

Slide the old brake pads out of the caliper bracket.
If necessary, remove any retaining clips or shims attached to the old pads.

5. Install New Brake Pads

Apply brake grease to the back of the new brake pads to prevent squealing.
Slide the new brake pads into the caliper bracket.
Reinstall any retaining clips or shims, ensuring they are properly seated.

6. Reinstall Brake Caliper

Use the C-clamp or brake caliper tool to compress the caliper piston into the caliper housing, making room for the new pads.
Position the caliper back over the new pads and align it with the bracket.
Reinstall and torque the caliper bolts to the manufacturer’s specifications (typically around 25-35 ft-lbs).

7. Reassemble Wheel

Place the wheel back onto the hub.
Hand-tighten the lug nuts and then lower the vehicle.
Once on the ground, torque the lug nuts to the manufacturer’s specifications (usually around 80-100 ft-lbs).