why does my Honda CR-V Sixth Generation (2023-present) make a clicking noise when turning

Honda CR-V Fifth Generation (2017-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

597 words

Problem Statement

Learn how to diagnose and fix clicking noise when turning in Honda CR-V Sixth Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Always use jack stands when lifting the vehicle for safety.

Symptoms

•Clicking or popping noise when turning the steering wheel
•Increased resistance or stiffness in the steering
•Vibration felt through the steering wheel
•Unusual tire wear patterns
•Check engine light may or may not be illuminated

Diagnostic Steps

1
Inspect the CV joints for wear or damage, particularly the outer joints.
2
Check for loose or damaged suspension components, such as control arms and bushings.
3
Examine the wheel bearings for play or noise during rotation.
4
Inspect the power steering fluid level and condition.
5
Test drive the vehicle to replicate the noise and assess when it occurs (sharp turns, low speeds, etc.).

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Pry bar
•CV joint removal tool
•Bearing puller (if necessary)
•OBD-II scanner (if needed)

Parts Required

•CV joint assembly (if damaged)
•Suspension components (if worn)
•Wheel bearing (if necessary)
•Power steering fluid

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints for wear or damage, particularly the outer joints.
2
Check for loose or damaged suspension components, such as control arms and bushings.
3
Examine the wheel bearings for play or noise during rotation.
4
Inspect the power steering fluid level and condition.
5
Test drive the vehicle to replicate the noise and assess when it occurs (sharp turns, low speeds, etc.).

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is on a level surface and securely lifted using jack stands.
Disconnect the battery to avoid any electrical issues during repair.

2. Inspect and Replace CV Joints

Tools Required: Socket set, torque wrench, pry bar, CV joint removal tool.
Steps:
1. Remove the wheel corresponding to the side making the noise.
2. Remove the axle nut using a socket wrench.
3. Use a pry bar to disconnect the CV joint from the wheel hub.
4. Inspect the CV joint for torn boots or visible grease leakage.
5. If damaged, replace the CV joint by reversing the removal steps, ensuring to torque the axle nut to manufacturer specifications (typically around 130-150 ft-lbs).

3. Inspect Suspension Components

Tools Required: Socket set, torque wrench.
Steps:
1. Visually inspect control arms, bushings, and ball joints for wear or damage.
2. If wear is found, replace the damaged components.
3. Torque all bolts to specifications as per the service manual (usually around 40-70 ft-lbs depending on the part).

4. Check Wheel Bearings

Tools Required: Socket set, torque wrench, bearing puller (if necessary).
Steps:
1. Spin the wheel to listen for grinding or roughness.
2. If noise is present, remove the wheel and inspect the wheel bearing.
3. Replace the wheel bearing if it is worn out by using a bearing puller, ensuring to properly seat the new bearing.

5. Inspect Power Steering System

Tools Required: OBD-II scanner (if needed).
Steps:
1. Check the power steering fluid level and top up if low.
2. Inspect for leaks in the power steering system.
3. If the fluid is contaminated, replace it and bleed the system according to the service manual.