how to fix Honda CR-V Fifth Generation (2017-2022) transmission jerking when shifting

Honda CR-V 6th Gen (2023-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

594 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission jerking in Honda CR-V Fifth Generation (2017-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Allow the engine to cool before working on the transmission.
•Disconnect the battery before working on electrical systems to prevent shorts.

Symptoms

•Jerking sensation during shifting between gears
•Delay in engagement of drive or reverse
•Unusual noise when shifting occurs
•Check Engine light illuminated
•Inconsistent acceleration response

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related faults.
2
Check transmission fluid level and condition for contamination or burning odors.
3
Inspect the transmission control module (TCM) for any visible damage or loose connections.
4
Test the transmission fluid temperature sensor using a multimeter.
5
Perform a road test to replicate the jerking and note specific conditions when it occurs.
6
Inspect engine mounts for wear or damage that may contribute to shifting issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Transmission fluid dipstick
•Socket set
•Torque wrench
•Funnel
•Drain pan
•Electrical cleaner

Parts Required

•Honda ATF DW-1 transmission fluid
•Transmission filter (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related faults.
2
Check transmission fluid level and condition for contamination or burning odors.
3
Inspect the transmission control module (TCM) for any visible damage or loose connections.
4
Test the transmission fluid temperature sensor using a multimeter.
5
Perform a road test to replicate the jerking and note specific conditions when it occurs.
6
Inspect engine mounts for wear or damage that may contribute to shifting issues.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is turned off.
Disconnect the battery to prevent electrical shorts during repair.

2. Check Transmission Fluid

Tools Required: Transmission fluid dipstick, funnel, clean rags
Sub-steps:
1. Locate the transmission dipstick and remove it.
2. Wipe the dipstick clean and reinsert it to check the fluid level.
3. If the fluid is low, add the recommended transmission fluid (Honda ATF DW-1) to the fill point.
4. Inspect fluid condition; if it appears dark or has a burnt smell, a fluid change is necessary.

3. Change Transmission Fluid

Tools Required: Socket set, drain pan, new transmission fluid (Honda ATF DW-1), funnel, replacement filter (if applicable)
Sub-steps:
1. Raise the vehicle safely using jack stands.
2. Place a drain pan under the transmission pan and remove the drain plug or pan bolts.
3. Allow the old fluid to fully drain.
4. Replace the transmission filter if applicable.
5. Reinstall the drain plug or transmission pan and torque to manufacturer specifications (usually around 10-15 lb-ft).
6. Refill the transmission with new fluid using a funnel.

4. Inspect and Repair TCM

Tools Required: Torque wrench, socket set, electrical cleaner
Sub-steps:
1. Locate the TCM, usually found near the transmission.
2. Disconnect the electrical connectors and remove the TCM from its mounting.
3. Clean the connectors with electrical cleaner to ensure a good electrical connection.
4. Reinstall the TCM and reconnect the wiring harness securely.

5. Test Drive

Tools Required: None
Sub-steps:
1. Reconnect the battery.
2. Start the vehicle and allow it to warm up.
3. Perform a test drive to check for any remaining jerking during shifting.