how to fix P0700 transmission code in Honda CR-V Fifth Generation (2017-2022)

Honda CR-V 6th Gen (2023-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0700

3 min read

592 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0700 transmission code in Honda CR-V (2017-2022). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Error Code

P0700

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the transmission.

Symptoms

•Check engine light illuminated
•Erratic or harsh shifting
•Transmission slipping
•Delayed engagement into gear
•Poor acceleration performance

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm the P0700 code and check for additional codes related to the transmission.
2
Inspect the transmission fluid level and condition; look for discoloration or burnt smell.
3
Check the wiring harness and connectors related to the transmission control module (TCM) for damage or corrosion.
4
Test the TCM using a multimeter to ensure it is receiving and sending the correct voltage.
5
Inspect the transmission filter for blockages or contamination.
6
Verify the operation of the vehicle speed sensor and input/output speed sensors.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Torque wrench
•Fluid catch pan

Parts Required

•Transmission fluid (Honda ATF DW-1)
•New TCM (if necessary)
•Vehicle speed sensor (if necessary)
•Input/output speed sensors (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm the P0700 code and check for additional codes related to the transmission.
2
Inspect the transmission fluid level and condition; look for discoloration or burnt smell.
3
Check the wiring harness and connectors related to the transmission control module (TCM) for damage or corrosion.
4
Test the TCM using a multimeter to ensure it is receiving and sending the correct voltage.
5
Inspect the transmission filter for blockages or contamination.
6
Verify the operation of the vehicle speed sensor and input/output speed sensors.

Solution

1. Preparation

Gather tools: OBD-II scanner, multimeter, socket set, torque wrench, fluid catch pan.
Ensure the vehicle is on a level surface and securely raised with jack stands if needed.
Disconnect the battery before working on electrical components.

2. Fluid Change

Sub-steps:
1. Locate the transmission fluid drain plug and place a fluid catch pan underneath.
2. Remove the drain plug using the appropriate socket and allow fluid to fully drain.
3. Replace the drain plug and torque it to the manufacturer’s specifications (usually around 30 ft-lbs).
4. Remove the transmission fluid fill plug.
5. Refill the transmission with the correct type of fluid (Honda ATF DW-1) through the fill hole until it reaches the proper level.

3. TCM Inspection and Replacement (if necessary)

Sub-steps:
1. Locate the TCM, typically found near the transmission or under the dashboard.
2. Disconnect the wiring harness from the TCM, checking for any signs of corrosion or damage.
3. Remove the TCM mounting bolts using a socket wrench.
4. Carefully remove the TCM and replace it with a new unit, ensuring it is securely mounted.
5. Reconnect the wiring harness, making sure it is seated properly.

4. Sensor Replacement (if necessary)

Sub-steps:
1. Locate the vehicle speed sensor and input/output speed sensors as indicated by the diagnostic code.
2. Disconnect the wiring harness from the sensors.
3. Remove the sensors using a socket or wrench.
4. Install new sensors, ensuring they are torqued to specifications.
5. Reconnect the wiring harness to each sensor.