why does my Honda CR-V Fifth Generation (2017-2022) shake when I accelerate

Honda CR-V Sixth Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

506 words

Problem Statement

Learn how to diagnose and fix shaking during acceleration in Honda CR-V (2017-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the vehicle to cool before inspecting components near the engine.

Symptoms

•Vehicle shakes or vibrates during acceleration
•Steering wheel vibration
•Unusual noise during acceleration (e.g., clunking or grinding)
•Increased steering responsiveness or instability
•Vibration may lessen at cruising speeds

Diagnostic Steps

1
Inspect tire condition and pressure for uneven wear or low inflation.
2
Check wheel balance and alignment to rule out misalignment issues.
3
Examine the CV joints and axles for damage or excessive wear.
4
Inspect the engine and transmission mounts for signs of deterioration.
5
Scan for error codes using an OBD-II scanner to identify possible engine or transmission issues.
6
Test drive the vehicle to replicate the shaking and assess when it occurs.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Lug wrench
•Torque wrench
•OBD-II scanner

Parts Required

•Tires (if needed)
•CV joint kit or axle shaft (if replacement is needed)
•Engine or transmission mounts (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect tire condition and pressure for uneven wear or low inflation.
2
Check wheel balance and alignment to rule out misalignment issues.
3
Examine the CV joints and axles for damage or excessive wear.
4
Inspect the engine and transmission mounts for signs of deterioration.
5
Scan for error codes using an OBD-II scanner to identify possible engine or transmission issues.
6
Test drive the vehicle to replicate the shaking and assess when it occurs.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and secure it with wheel chocks.
Disconnect the battery to avoid electrical shorts during repair.

2. Tire Inspection and Replacement

Sub-steps:
1. Remove the wheel covers or hubcaps if applicable.
2. Loosen the lug nuts slightly but do not remove them.
3. Raise the vehicle using a jack and secure it on jack stands.
4. Remove the lug nuts and take off the wheels for inspection.
Tools Required: Jack, jack stands, lug wrench.

3. Check and Balance Tires

Sub-steps:
1. Inspect tires for uneven wear or damage; replace if necessary.
2. Take tires to a shop for balancing.
3. Reinstall tires and torque lug nuts to manufacturer specifications (typically 80-100 ft-lbs).
Tools Required: Torque wrench.

4. Inspect CV Joints and Axles

Sub-steps:
1. Visually inspect the CV boots for tears or leaks.
2. Check for play in the CV joints; replace if worn or damaged.
3. Remove the axle shaft if necessary for replacement.
Parts Required: CV joint kit or axle shaft if replacement is needed.

5. Engine and Transmission Mounts

Sub-steps:
1. Visually inspect engine and transmission mounts for cracks or wear.
2. Replace any mounts that show signs of deterioration.
Parts Required: Engine or transmission mount(s) as needed.