FAULTBASE
Error CodesASKCars
© 2026 FAULTBASE
All rights reserved.
v2.0.0 • Production
ContactPrivacyImpressum
how to fix the traction control light on Ram 1500 DT (2019-Present) - Ram 1500
Home/Cars/Ram/1500/DT (2019-Present)/how to fix the traction control light on Ram 1500 DT (2019-Present)

how to fix the traction control light on Ram 1500 DT (2019-Present)

Ram 1500 DT (2019-Present)

Error Codes
1-3 hours
Time
medium
Difficulty
medium
Severity
Navigation
ProblemSymptomsDiagnosisSolution
ProblemSymptomsDiagnosisSolution
3 min read
541 words

Problem Statement

Learn how to diagnose and fix the traction control light issue on Ram 1500 DT (2019-Present). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component
Electrical
Estimated Time
1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

  • •Disconnect the battery before working on electrical systems.
  • •Allow the vehicle to cool down before inspecting brake components.

Symptoms

  • •Traction control light is illuminated on the dashboard
  • •Reduced engine power during acceleration
  • •Unusual wheel slip or spinning during acceleration
  • •Possible activation of ABS warning light
  • •Intermittent loss of traction control functionality

Diagnostic Steps

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

  • ✓Test the affected component to ensure it functions correctly
  • ✓Check for any error codes or warning lights
  • ✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

  • •Follow the manufacturer's recommended maintenance schedule
  • •Address warning signs early before they develop into major issues
  • •Use quality parts and fluids recommended for your vehicle
  • •Keep detailed records of all repairs and maintenance

Tools & Equipment Required

  • •OBD-II scanner
  • •Socket set
  • •Multimeter
  • •Cleaning supplies

Parts Required

  • •Replacement wheel speed sensors (if faulty)
  • •Replacement traction control switch (if faulty)
  • •Brake pads and rotors (if worn)

Additional Information

Affected Component
Electrical
Estimated Time
1-3 hours
Difficulty
medium
Severity
medium
Tools Required
4 items
Parts Required
3 items

Related Faults

Loading...

Share this solution

Comments

Sign in to share your thoughts

Sign In

No comments yet

Be the first to share your thoughts

Back to Generation
Solution
1. Preparation
  • Tools Required: OBD-II scanner, socket set, multimeter, cleaning supplies
  • Disconnect the negative battery terminal to ensure safety before working on the vehicle.
2. Address Error Codes
  • Connect the OBD-II scanner to the vehicle’s diagnostic port.
  • Retrieve and note any error codes related to the traction control system.
  • Clear the error codes and see if they reappear after a short test drive.
3. Inspect and Clean Wheel Speed Sensors
  • Locate the wheel speed sensors on each wheel hub.
  • Remove any dirt or debris around the sensors using a soft cloth.
  • Check sensor connectors for corrosion; clean if necessary.
  • Reconnect the sensors and ensure they are securely mounted.
4. Verify Traction Control Switch
  • Locate the traction control switch on the dashboard.
  • Test the switch with a multimeter to ensure it is functioning properly.
  • If the switch is faulty, replace it with a new one.
5. Brake System Inspection
  • Check brake pads and rotors for excessive wear or damage.
  • Inspect the brake fluid reservoir to ensure it is at the correct level.
  • Replace any worn components and top off the brake fluid as needed.
6. Reconnect Battery
  • Reconnect the negative battery terminal securely.
  • Start the vehicle and check if the traction control light is still illuminated.