why does my Renault Clio V (2019-Present) suspension feel bouncy

Renault Clio V (2019-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

492 words

Problem Statement

Learn how to diagnose and fix bouncy suspension in Renault Clio V (2019-Present). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the vehicle is securely supported on jack stands before working underneath.
•Disconnect the battery before working on electrical components, if applicable.

Symptoms

•Excessive bouncing after hitting bumps or potholes
•Poor handling and stability during cornering
•Increased noise from the suspension over rough surfaces
•Uneven tire wear on front or rear tires
•Check suspension warning light illuminated (if equipped)

Diagnostic Steps

1
Inspect the visual condition of the shocks and struts for leaks or physical damage.
2
Check tire pressure and condition, ensuring they are at manufacturer specifications.
3
Perform a bounce test by pressing down on each corner of the vehicle and observing rebound.
4
Inspect suspension bushings and mounts for wear or damage.
5
Scan the vehicle for any suspension-related error codes using an OBD-II scanner.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•OBD-II scanner

Parts Required

•Replacement dampers (front or rear as needed)
•Suspension bushings (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the visual condition of the shocks and struts for leaks or physical damage.
2
Check tire pressure and condition, ensuring they are at manufacturer specifications.
3
Perform a bounce test by pressing down on each corner of the vehicle and observing rebound.
4
Inspect suspension bushings and mounts for wear or damage.
5
Scan the vehicle for any suspension-related error codes using an OBD-II scanner.

Solution

1. Preparation

Gather tools and parts needed for replacement.
Park the vehicle on a level surface and engage the parking brake.
Wear safety gloves and goggles.

2. Raise the Vehicle

Use a jack to lift the vehicle at the recommended lifting points.
Secure the vehicle with jack stands for safety.

3. Remove the Wheel

Using a socket set, remove the lug nuts and take off the wheel to access the suspension components.

4. Remove the Damper

Disconnect any connected components (e.g., sway bar link, brake line) with appropriate tools.
Remove bolts securing the damper to the mounting points using a torque wrench.
Carefully take out the damper from its position.

5. Inspect and Replace

Inspect the old damper for signs of wear or leakage.
Install the new damper into position, ensuring proper alignment with the mounting points.
Torque the bolts to the manufacturer’s specifications (refer to the service manual).

6. Reassemble

Reconnect any components that were disconnected.
Replace the wheel and torque the lug nuts to the manufacturer’s specifications.
Lower the vehicle from the jack stands.

7. Final Check

Ensure all tools are removed from the vehicle area before starting.
Test the new suspension setup by gently driving over bumps to check for improved stability.