how to reset the check engine light in Tesla Outback 5th Generation (2015-2019)

Subaru Outback 5th Generation (2015-2019)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

519 words

Problem Statement

Learn how to reset the check engine light in a 2015-2019 Subaru Outback. Step-by-step guide with diagnostic procedures and safety tips.

Affected Component

Engine

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the vehicle is powered off and the keys are removed from the ignition before disconnecting the battery.
•Disconnect battery before working on electrical systems.

Symptoms

•Check engine light illuminated on the dashboard
•Potential loss of vehicle performance
•No other warning lights activated
•Possible rough idle or engine noise

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify the underlying issue causing the CEL.
2
Address any detected error codes by performing necessary repairs or maintenance.
3
Disconnect the negative terminal of the battery for 10-15 minutes to reset the light.
4
Reconnect the battery terminal and turn the ignition to the 'ON' position without starting the engine to check if the light remains off.
5
Conduct a test drive to ensure the check engine light does not reappear.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Battery terminal wrench

Parts Required

•Replacement parts as needed based on error codes (e.g., sensors, gaskets).

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify the underlying issue causing the CEL.
2
Address any detected error codes by performing necessary repairs or maintenance.
3
Disconnect the negative terminal of the battery for 10-15 minutes to reset the light.
4
Reconnect the battery terminal and turn the ignition to the 'ON' position without starting the engine to check if the light remains off.
5
Conduct a test drive to ensure the check engine light does not reappear.

Solution

1. Preparation

Gather necessary tools: OBD-II scanner, socket set, and a battery terminal wrench.
Ensure the vehicle is parked in a safe, level area and the engine is off.
Wear safety gloves and goggles for protection.

2. Read Error Codes

Connect the OBD-II scanner to the vehicle’s OBD-II port (typically located under the dashboard).
Turn the ignition to the "ON" position (do not start the engine).
Follow the scanner’s instructions to read and record any error codes.

3. Address Underlying Issues

If error codes are present, research and perform repairs associated with those codes (e.g., replacing sensors, fixing leaks).
Clear the error codes using the OBD-II scanner after repairs are made.

4. Reset Check Engine Light

Disconnect the negative battery terminal using a socket wrench.
- Safety Warning: Ensure the vehicle is powered off and the keys are removed from the ignition before disconnecting the battery.
Wait for 10-15 minutes to allow the vehicle’s systems to reset.
Reconnect the negative battery terminal securely.

5. Final Check

Turn the ignition to the "ON" position without starting the engine.
Observe the dashboard for any warning lights.
Start the engine and monitor for a few minutes to ensure the check engine light remains off.