how to fix a P0135 code on my Toyota Camry Eighth Generation (2018-present)?

Toyota Camry Eighth Generation (2018-present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

Error Code: P0135

3 min read

504 words

Problem Statement

Learn how to diagnose and fix P0135 oxygen sensor issue in Toyota Camry. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0135

Affected Component

Exhaust System

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the exhaust system to avoid burns.

Symptoms

•Check engine light illuminated
•Decreased fuel efficiency
•Rough engine idle
•Poor engine performance or acceleration
•Increased exhaust emissions

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0135 and check for any related codes.
2
Inspect the wiring and connectors of the upstream oxygen sensor for damage or corrosion.
3
Check the sensor's heater circuit using a multimeter to ensure it is functioning properly.
4
Verify the oxygen sensor's operation by monitoring the voltage output with a scan tool while the engine is running.
5
Inspect the engine’s exhaust system for leaks that may affect sensor readings.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Torque wrench
•Oxygen sensor socket

Parts Required

•New upstream oxygen sensor

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0135 and check for any related codes.
2
Inspect the wiring and connectors of the upstream oxygen sensor for damage or corrosion.
3
Check the sensor's heater circuit using a multimeter to ensure it is functioning properly.
4
Verify the oxygen sensor's operation by monitoring the voltage output with a scan tool while the engine is running.
5
Inspect the engine’s exhaust system for leaks that may affect sensor readings.

Solution

1. Preparation

Tools Required: OBD-II scanner, multimeter, socket set, torque wrench, oxygen sensor socket.
Allow the engine to cool before starting work on the exhaust system.

2. Disconnect the Battery

Disconnect the negative terminal of the battery to prevent electrical shock.

3. Remove the Faulty Oxygen Sensor

Locate the upstream oxygen sensor (typically found before the catalytic converter).
Use an oxygen sensor socket to carefully unscrew and remove the faulty sensor.
Be cautious to avoid damaging the sensor wiring.

4. Inspect and Clean Connectors

Examine the connectors leading to the oxygen sensor for corrosion or damage.
Clean any corrosion with electrical contact cleaner and a soft brush. Ensure that the connectors are dry before reassembly.

5. Install New Oxygen Sensor

Apply anti-seize compound to the threads of the new oxygen sensor (if not pre-applied).
Install the new oxygen sensor by threading it into the exhaust pipe and tightening it to the manufacturer's specified torque (usually around 30 ft-lbs).
Reconnect the oxygen sensor connector securely.

6. Reconnect the Battery

Reattach the negative terminal of the battery and ensure it is tight.

7. Clear the Codes

Use the OBD-II scanner to clear the P0135 code from the vehicle's computer.
Start the engine and allow it to reach operating temperature.