How to fix the windshield wipers not working in a 2021 Toyota Camry XV70?

Toyota Camry XV70 (2018-2024)

Error Codes

medium

Difficulty

medium

Severity

4 min read

650 words

Problem Statement

Learn how to diagnose and repair windshield wipers not working in a 2021 Toyota Camry XV70 with detailed steps and required tools.

Affected Component

windshield wipers

Symptoms

•Wipers Not Moving
•Partial Movement
•No Sound
•Wipers Stuck

Diagnostic Steps

1
Check Wiper Switch
2
Inspect Fuses
3
Test Wiper Motor
4
Check Wiper Linkage

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Multimeter
•Fuse puller or needle-nose pliers
•14mm socket and ratchet
•Screwdriver set (flathead and Phillips)
•Torque wrench (if needed for reassembly)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Fixing Windshield Wipers Not Working in a 2021 Toyota Camry XV70

Step 1: Check Wiper Switch

Action: Turn the ignition to "ON" and operate the wiper switch in all positions (intermittent, low, high).
Expected Result: The wipers should respond to the switch. If there is no response, the switch may be faulty.

Step 2: Inspect Fuses

Tool Required: Fuse puller or needle-nose pliers.
Action: Locate the fuse box (usually under the dashboard or in the engine bay). Check the wiper fuse (refer to the owner's manual for the exact location).
Expected Result: If the fuse is blown, replace it and test the wipers again.

Step 3: Test Wiper Motor

Tool Required: Multimeter.
Action: Disconnect the wiper motor connector. Use the multimeter to check for voltage at the connector while activating the wiper switch.
Expected Result: You should see approximately 12V when the wipers are activated. If there is no voltage, the issue may be in the wiring or switch.

Step 4: Check Wiper Linkage

Action: Manually inspect the wiper linkage by removing the wiper arms (use a 14mm socket) and check for any obstructions or damage.
Expected Result: The linkage should move freely without obstruction. If it is stuck, lubricate or replace it.

Tools Required

Multimeter
Fuse puller or needle-nose pliers
14mm socket and ratchet
Screwdriver set (flathead and Phillips)
Torque wrench (if needed for reassembly)

Repair Instructions

Repair Option 1: Replace Wiper Fuse

Locate the Fuse: Open the fuse box and locate the wiper fuse using the diagram.
Remove the Fuse: Use the fuse puller to carefully remove the blown fuse.
Replace the Fuse: Insert a new fuse of the same amperage.
Test Wipers: Turn on the ignition and test the wipers.

Repair Option 2: Replace Wiper Motor

Disconnect Battery: Disconnect the negative terminal of the battery to prevent electrical shorts.
Remove Wiper Arms: Using a 14mm socket, remove the nuts holding the wiper arms and lift them off.
Access Wiper Motor: Depending on the model, you may need to remove the cowl cover (often secured with clips or screws) to access the wiper motor.
Disconnect Motor: Unplug the electrical connector from the motor.
Remove Motor: Remove the mounting bolts (usually 10mm) securing the wiper motor and take it out.
Install New Motor: Position the new wiper motor in place, secure it with bolts, and reconnect the electrical connector.
Reassemble Wiper Arms: Reattach the wiper arms, ensuring they are positioned correctly. Tighten the nuts securely.
Reconnect Battery: Reconnect the negative battery terminal.
Test Wipers: Turn on the ignition and test the wipers for functionality.

Repair Option 3: Replace Wiper Switch

Access Switch: Remove the steering column covers using a screwdriver.
Disconnect Battery: To prevent shorts, disconnect the battery.
Remove Switch: Unscrew the wiper switch from the steering column and disconnect the wiring harness.
Install New Switch: Connect the new switch and secure it in place.
Reassemble Column: Reattach the steering column covers.
Reconnect Battery: Reconnect the negative terminal.
Test Wipers: Turn on the ignition and test the switch for proper operation.

Conclusion

By following these detailed steps, you should be able to diagnose and repair the windshield wiper issue in your 2021 Toyota Camry XV70. If the problem persists after these repairs, consider consulting a professional technician for further analysis.