how to fix my Toyota Camry XV70 (2018-2024) that shakes when braking

Toyota Camry XV80 (2025-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

609 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to fix shaking when braking in Toyota Camry XV70 (2018-2024). Step-by-step guide with diagnostic steps, tools, and parts required.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on the braking system to prevent any electrical issues.
•Ensure the vehicle is securely lifted and supported before working underneath it.

Symptoms

•Shaking or vibration felt in the steering wheel during braking
•Pulsation in the brake pedal
•Uneven wear on brake pads or rotors
•Noise during braking (squeaking or grinding)
•Longer stopping distances
•Increased brake dust on wheels

Diagnostic Steps

1
Inspect brake rotors for warping or uneven wear using a dial indicator.
2
Check brake pads for thickness and even wear patterns.
3
Examine brake calipers for proper operation and any sticking issues.
4
Inspect wheel bearings for play or damage.
5
Verify tire condition and balance; check for uneven wear or damage.
6
Scan for any related error codes using an OBD-II scanner to rule out electronic brake issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Brake rotor gauge
•Dial indicator
•Brake cleaner

Parts Required

•New brake rotors
•New brake pads

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake rotors for warping or uneven wear using a dial indicator.
2
Check brake pads for thickness and even wear patterns.
3
Examine brake calipers for proper operation and any sticking issues.
4
Inspect wheel bearings for play or damage.
5
Verify tire condition and balance; check for uneven wear or damage.
6
Scan for any related error codes using an OBD-II scanner to rule out electronic brake issues.

Solution

1. Preparation

Gather tools: socket set, torque wrench, brake rotor gauge, dial indicator, and brake cleaner.
Ensure the vehicle is parked on a flat surface, and engage the parking brake.
Wear safety glasses and gloves.

2. Remove Wheel

Loosen lug nuts slightly while the wheel is on the ground.
Lift the vehicle using a jack and securely place jack stands.
Remove the lug nuts completely and take off the wheel.

3. Inspect and Replace Brake Rotors

Check Rotor Condition:
- Use a dial indicator to measure any warping; replace if warping exceeds manufacturer specifications (usually 0.002 inches).
Remove Brake Caliper:
- Remove caliper bolts using a socket.
- Support the caliper using a bungee cord or rope to avoid straining the brake line.
Remove Brake Rotor:
- If the rotor is held by retaining screws, remove them.
- Slide the rotor off the hub; clean the hub surface with brake cleaner.
Install New Rotor:
- Place the new rotor onto the hub, ensuring it is seated properly.
- Reinstall retaining screws if applicable.

4. Inspect and Replace Brake Pads

Check Pad Thickness:
- Measure the thickness; replace if under manufacturer specifications (usually 1/8 inch).
Remove Old Pads:
- Slide out the old brake pads from the caliper bracket.
Install New Pads:
- Apply anti-squeal lubricant to the back of the new pads.
- Install the new pads into the caliper bracket.

5. Reassemble and Torque

Reinstall Caliper:
- Position the caliper over the new pads and secure it with caliper bolts.
- Torque caliper bolts to manufacturer specifications (usually 25-35 ft-lbs).
Reinstall Wheel:
- Place the wheel back on the hub.
- Hand-tighten the lug nuts before lowering the vehicle.
Lower Vehicle:
- Remove jack stands and lower the vehicle to the ground.
- Torque lug nuts to manufacturer specifications (usually 76-80 ft-lbs).