how to fix the door ajar light staying on in my Toyota Camry XV70 (2018-2024)

Toyota Camry XV80 (2025-Present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

529 words

Problem Statement

Learn how to diagnose and fix the door ajar light issue in Toyota Camry XV70 (2018-2024). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Electrical

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components to avoid shorts.

Symptoms

•Door ajar warning light is illuminated on the dashboard
•Doors may appear to be securely closed
•Chimes or alerts sounding when the vehicle is in motion
•Battery drain due to the internal lights staying on
•Possible malfunction of interior lights not turning off

Diagnostic Steps

1
Inspect all doors to ensure they are fully closed and latched.
2
Check the door switches for physical damage or misalignment.
3
Use an OBD-II scanner to check for any related trouble codes.
4
Test each door switch with a multimeter to verify continuity when the door is open and closed.
5
Inspect the wiring harness connected to the door switches for any signs of damage or corrosion.
6
Check the vehicle’s body control module (BCM) for any fault that could cause the issue.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Phillips screwdriver
•Flathead screwdriver
•Wire stripper/crimper

Parts Required

•Door switch (if faulty)
•Electrical connectors (if wiring repair is needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect all doors to ensure they are fully closed and latched.
2
Check the door switches for physical damage or misalignment.
3
Use an OBD-II scanner to check for any related trouble codes.
4
Test each door switch with a multimeter to verify continuity when the door is open and closed.
5
Inspect the wiring harness connected to the door switches for any signs of damage or corrosion.
6
Check the vehicle’s body control module (BCM) for any fault that could cause the issue.

Solution

1. Preparation

Gather the necessary tools and parts.
Park the vehicle on a level surface and ensure it is in "Park" mode.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Inspect Door Switches

Tools Required: Phillips screwdriver, flathead screwdriver
Remove the door panel using a Phillips screwdriver to access the door switch.
Check the physical condition of the door switch for dirt or debris. Clean if necessary.
Ensure the switch moves freely and is not stuck.

3. Test Door Switches

Tools Required: Multimeter
Connect the multimeter leads to the terminals of the door switch.
With the door open, check for continuity; the multimeter should show an open circuit.
Close the door and check for continuity; the multimeter should show a closed circuit.
If the switch does not operate as tested, replace it.

4. Inspect Wiring Harness

Tools Required: Wire stripper/crimper, electrical tape
Inspect the wiring connected to the door switches for any fraying or breaks.
Repair any damaged wires using a wire stripper and electrical tape or replace the affected section of the harness.

5. Reassemble and Test

Reinstall the door panel securely.
Reconnect the negative battery terminal.
Test the system by opening and closing each door to ensure the door ajar light functions correctly.