how to fix my Toyota Corolla E170 (2013-2019) transmission slipping when accelerating

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

501 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission slipping in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening any components associated with the transmission.

Symptoms

•Transmission slips during acceleration
•Engine RPMs increase without corresponding vehicle speed
•Delayed engagement when shifting from park to drive
•Check engine light illuminated
•Unusual noises during gear changes

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics (OBD-II) for any error codes related to the transmission.
2
Check the transmission fluid level and condition (color, smell).
3
Inspect for any visible leaks around the transmission and fluid lines.
4
Test the transmission fluid pressure using a pressure gauge.
5
Verify the operation of the transmission control module (TCM) and related sensors.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Transmission fluid pressure gauge
•Socket set
•Torque wrench
•Funnel
•Shop towels

Parts Required

•Toyota ATF WS transmission fluid
•Transmission filter
•Gasket for transmission pan

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics (OBD-II) for any error codes related to the transmission.
2
Check the transmission fluid level and condition (color, smell).
3
Inspect for any visible leaks around the transmission and fluid lines.
4
Test the transmission fluid pressure using a pressure gauge.
5
Verify the operation of the transmission control module (TCM) and related sensors.

Solution

1. Preparation

Tools Required: OBD-II scanner, transmission fluid pressure gauge, socket set, torque wrench, funnel, shop towels.
Ensure the vehicle is parked on a level surface and the engine is cooled down.
Disconnect the battery to avoid any electrical issues during repair.

2. Check and Replace Transmission Fluid

Sub-steps:
1. Remove the transmission dipstick and check the fluid level.
2. If fluid is low, add the appropriate type of transmission fluid (Toyota ATF WS) using a funnel.
3. If the fluid is dark, burnt, or has debris, proceed to drain the transmission fluid.
4. Locate the transmission drain plug, remove it, and let the fluid drain into a catch pan.
5. Replace the drain plug and torque it to 29 ft-lb (39 Nm).
6. Refill the transmission with fresh Toyota ATF WS fluid through the dipstick tube.

3. Inspect and Clean Transmission Filter

Sub-steps:
1. Remove the transmission pan by loosening the bolts with a socket set.
2. Carefully lower the pan and replace the transmission filter.
3. Clean the transmission pan and magnet to remove any metal shavings.
4. Reinstall the pan, ensuring a proper gasket seal, and tighten bolts to 74 in-lb (8.4 Nm).

4. Reprogram/Reset Transmission Control Module (if necessary)

Sub-steps:
1. Reconnect the battery.
2. Use an OBD-II scanner to reset the transmission control module.
3. Clear any stored error codes.