how to fix P0455 EVAP code on my Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

Error Code: P0455

3 min read

563 words

Problem Statement

Learn how to diagnose and fix P0455 EVAP code in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Error Code

P0455

Affected Component

Fuel System

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the vehicle to cool before working on the fuel system components.

Symptoms

•Check engine light illuminated
•Decreased fuel efficiency
•Strong fuel odor near the vehicle
•Failed emissions test
•Hissing sound from the fuel tank area during refueling

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0455 and check for any additional codes.
2
Inspect the EVAP system components visually for any obvious signs of damage or disconnection.
3
Check the gas cap for cracks, proper sealing, and ensure it is tightened correctly.
4
Perform a smoke test on the EVAP system to locate any leaks.
5
Inspect the EVAP hoses for cracks, leaks, or disconnections.
6
Test the EVAP purge valve and vent valve operation using a multimeter.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Screwdriver set
•Torque wrench

Parts Required

•New gas cap (if necessary)
•EVAP hoses (if damaged)
•EVAP purge valve (if faulty)
•EVAP vent valve (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0455 and check for any additional codes.
2
Inspect the EVAP system components visually for any obvious signs of damage or disconnection.
3
Check the gas cap for cracks, proper sealing, and ensure it is tightened correctly.
4
Perform a smoke test on the EVAP system to locate any leaks.
5
Inspect the EVAP hoses for cracks, leaks, or disconnections.
6
Test the EVAP purge valve and vent valve operation using a multimeter.

Solution

1. Preparation

Gather tools and parts required for the repair.
Disconnect the negative terminal of the battery to ensure safety.
Allow the engine to cool down if recently operated.

2. Inspect and Replace the Gas Cap

Remove the gas cap and inspect for cracks or damage.
If damaged, replace with a new gas cap that meets OEM specifications.
Ensure the gas cap is tightened securely after replacement.

3. Repair or Replace EVAP Hoses

Follow the hoses from the fuel tank to the EVAP canister.
If any hoses are damaged or disconnected, replace them with new hoses.
Use a hose clamp to secure connections as needed.

4. Test and Replace EVAP Purge Valve (if necessary)

Locate the EVAP purge valve, usually mounted on or near the intake manifold.
Disconnect the electrical connector and vacuum lines.
Using a multimeter, test the valve operation according to the service manual specifications.
If faulty, replace the valve with a new unit.

5. Test and Replace EVAP Vent Valve (if necessary)

Locate the EVAP vent valve, typically found near the fuel tank.
Disconnect the electrical connector and vacuum lines.
Test the valve operation with a multimeter.
Replace the vent valve if it fails the test.

6. Reconnect Battery and Clear Codes

Reconnect the negative terminal of the battery.
Use the OBD-II scanner to clear any stored codes.
Start the engine and verify that the check engine light is off.