how to fix P0700 code in Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0700

3 min read

428 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0700 transmission control system malfunction in Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0700

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the engine to cool before inspecting the transmission fluid.

Symptoms

•Check engine light illuminated
•Erratic shifting or slipping
•Delayed engagement into gear
•Transmission overheating
•Reduced fuel efficiency

Diagnostic Steps

1
Scan the vehicle’s computer using an OBD-II scanner to confirm the P0700 code and check for any additional transmission-related codes.
2
Inspect the transmission fluid level and condition; look for signs of contamination or burning.
3
Check the transmission wiring harness and connectors for damage or corrosion.
4
Inspect the transmission control module (TCM) for any signs of moisture or damage.
5
Test the transmission solenoids for proper operation using a multimeter.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Multimeter
•Torque wrench
•Jack and jack stands

Parts Required

•Toyota ATF WS transmission fluid
•Transmission filter (if applicable)
•Transmission control module (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle’s computer using an OBD-II scanner to confirm the P0700 code and check for any additional transmission-related codes.
2
Inspect the transmission fluid level and condition; look for signs of contamination or burning.
3
Check the transmission wiring harness and connectors for damage or corrosion.
4
Inspect the transmission control module (TCM) for any signs of moisture or damage.
5
Test the transmission solenoids for proper operation using a multimeter.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the negative battery terminal to prevent electrical shorts.
Ensure the vehicle is on a level surface and use jack stands for added safety if raising the vehicle.

2. Inspect and Replace Transmission Fluid

Sub-steps:
1. Locate the transmission dipstick and remove it to check fluid level.
2. If low, add the correct type of transmission fluid as specified in the owner’s manual (Toyota ATF WS).
3. If fluid is dirty or burnt, drain and replace the transmission fluid.
4. Replace the transmission filter if applicable.

3. Repair Wiring and Connectors

Sub-steps:
1. Visually inspect the wiring harness and connectors leading to the TCM and solenoids.
2. Repair or replace any damaged wires or connectors.
3. Ensure all connections are secure.

4. Test and Replace Transmission Control Module (if necessary)

Sub-steps:
1. If the TCM shows signs of damage, remove it from its mounting location.
2. Disconnect the wiring harness from the TCM and remove it.
3. Install the new TCM by reversing the removal steps.
4. Reconnect the wiring harness and ensure a snug fit.

5. Clear Codes and Test Drive

Sub-steps:
1. Reconnect the negative battery terminal.
2. Use the OBD-II scanner to clear the P0700 code and any other related codes.
3. Test drive the vehicle to ensure proper operation of the transmission.

Tools Required:

OBD-II scanner
Socket set
Multimeter
Torque wrench
Jack and jack stands

Parts Required:

Toyota ATF WS transmission fluid
Transmission filter (if applicable)
Transmission control module (if necessary)

Estimated Repair Time: 2-4 hours

Safety Warnings:

Disconnect the battery before working on electrical components.
Allow the engine to cool before inspecting the transmission fluid.