how to fix P0700 code on Toyota Corolla E170 (2013-2019)?

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0700

3 min read

565 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0700 transmission control system malfunction in Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0700

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow engine to cool before opening the hood or working on the transmission.

Symptoms

•Check engine light illuminated
•Transmission slipping or harsh shifting
•Loss of acceleration or power
•Unusual engine RPM fluctuations
•Delayed engagement when shifting into gear

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm the presence of P0700 and check for any additional transmission-related codes.
2
Inspect the transmission fluid level and condition (look for discoloration or debris).
3
Check the wiring and connectors to the transmission control module for damage or corrosion.
4
Verify the operation of the transmission range sensor (or neutral safety switch).
5
Test the TCM for proper voltage and ground using a multimeter.
6
Check for any external leaks around the transmission casing.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Transmission fluid dipstick
•Clean rags
•Wire strippers/crimpers
•Electrical tape
•Multimeter
•Socket set
•Torque wrench
•Funnel

Parts Required

•Transmission fluid
•Transmission range sensor (if needed)
•Transmission control module (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm the presence of P0700 and check for any additional transmission-related codes.
2
Inspect the transmission fluid level and condition (look for discoloration or debris).
3
Check the wiring and connectors to the transmission control module for damage or corrosion.
4
Verify the operation of the transmission range sensor (or neutral safety switch).
5
Test the TCM for proper voltage and ground using a multimeter.
6
Check for any external leaks around the transmission casing.

Solution

1. Preparation

Gather all necessary tools and parts.
Disconnect the negative battery terminal to prevent electrical shorts.
Ensure the vehicle is on a level surface and safely supported with jack stands.

2. Inspect Transmission Fluid

Tools Required: Transmission fluid dipstick, clean rags.
Check the fluid level using the dipstick; add fluid if low.
Inspect the fluid for contamination; if dirty or burnt, proceed to replace the fluid.

3. Repair Wiring and Connectors

Tools Required: Wire strippers/crimpers, electrical tape, multimeter.
Visually inspect the wiring harness and connectors to the TCM.
Repair any damaged wires using solder or crimp connectors, and secure with electrical tape.

4. Replace Transmission Range Sensor (if faulty)

Tools Required: Socket set, torque wrench.
Locate the transmission range sensor on the transmission.
Disconnect the wiring harness.
Remove the bolts securing the sensor and replace it with a new unit.
Torque the bolts to the manufacturer's specifications.

5. Replace Transmission Control Module (if necessary)

Tools Required: Socket set, torque wrench.
Disconnect the battery and locate the TCM.
Disconnect the wiring harness from the TCM.
Remove mounting bolts and take out the old TCM.
Install the new TCM and reconnect the wiring harness.
Torque bolts to manufacturer specifications.

6. Refill Transmission Fluid

Tools Required: Funnel, transmission fluid.
Refill the transmission with manufacturer-recommended fluid through the dipstick tube.
Start the engine and allow it to reach operating temperature, then check the fluid level again.