how to fix the grinding noise in my Toyota Corolla E170 (2013-2019) when driving

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

535 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix grinding noise in Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the vehicle to cool before working on brake components.

Symptoms

•Grinding noise when the vehicle is in motion
•Noise may increase with acceleration or cornering
•Possible vibration felt through the steering wheel or floor
•Uneven tire wear or damage
•Check engine light may illuminate if related to drivetrain issues

Diagnostic Steps

1
Inspect brake components for wear or damage, including pads, rotors, and calipers.
2
Check wheel bearings by lifting the vehicle and spinning each wheel to feel for roughness or noise.
3
Examine tires for uneven wear patterns or foreign objects lodged in the tread.
4
Inspect the drivetrain components, including CV joints and axles, for wear or damage.
5
Test drive the vehicle to pinpoint the noise location and conditions under which it occurs.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Lug wrench
•Jack and jack stands
•Torque wrench
•Bearing puller
•Socket set
•Screwdrivers

Parts Required

•Brake pads
•Brake rotors
•Wheel bearings
•CV joint or axle (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake components for wear or damage, including pads, rotors, and calipers.
2
Check wheel bearings by lifting the vehicle and spinning each wheel to feel for roughness or noise.
3
Examine tires for uneven wear patterns or foreign objects lodged in the tread.
4
Inspect the drivetrain components, including CV joints and axles, for wear or damage.
5
Test drive the vehicle to pinpoint the noise location and conditions under which it occurs.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical components.

2. Inspect and Replace Brake Components

Sub-steps:
1. Remove the wheel using a lug wrench and jack stands for safety.
2. Inspect brake pads for thickness and wear; replace if less than 3mm.
3. Check the brake rotors for scoring or warping; replace if necessary.
4. Reinstall wheel and torque lug nuts to manufacturer specifications (typically 76 ft-lbs for Corolla).

3. Check and Replace Wheel Bearings

Sub-steps:
1. Lift the vehicle and secure it on jack stands.
2. Remove the wheel and brake assembly to access the wheel bearing.
3. Inspect the bearing for play or roughness; replace if defective.
4. Use a bearing puller to remove the old bearing and install the new one.
5. Reassemble the brake assembly and wheel, ensuring everything is tightened to specifications.

4. Inspect and Replace Drivetrain Components

Sub-steps:
1. Inspect CV joints for any tears in the boot or excess grease leakage.
2. If necessary, remove the axle by unbolting it from the transmission and hub.
3. Replace the CV joint or axle as needed, ensuring proper alignment and securing all bolts to torque specifications.
4. Reinstall the wheel and lower the vehicle.