how to fix transmission slipping in my Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

611 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission slipping in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Allow the engine to cool before working on the transmission.
•Disconnect the battery before working on electrical components.

Symptoms

•Engine revs higher than normal without corresponding acceleration
•Delayed or harsh shifting between gears
•Transmission warning light illuminated on the dashboard
•Fluid leaks under the vehicle
•Poor fuel economy
•Unusual noises during acceleration or shifting

Diagnostic Steps

1
Check the transmission fluid level and condition.
2
Scan the vehicle's computer for any transmission-related trouble codes using an OBD-II scanner.
3
Inspect the transmission fluid for contamination or burnt smell.
4
Examine the transmission filter for clogs or blockages.
5
Inspect electrical connections and wiring to the transmission control module.
6
Test the transmission solenoids for proper operation.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Multimeter
•Fluid pump
•Funnel

Parts Required

•Toyota ATF WS transmission fluid
•Transmission filter
•Transmission pan gasket
•Transmission solenoids (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the transmission fluid level and condition.
2
Scan the vehicle's computer for any transmission-related trouble codes using an OBD-II scanner.
3
Inspect the transmission fluid for contamination or burnt smell.
4
Examine the transmission filter for clogs or blockages.
5
Inspect electrical connections and wiring to the transmission control module.
6
Test the transmission solenoids for proper operation.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the battery to eliminate electrical hazards.

2. Check and Replace Transmission Fluid

Tools Required: Socket set, transmission fluid pump, funnel.
Steps:
1. Locate the transmission dipstick and remove it.
2. Check the fluid level; if low, add the recommended transmission fluid (Toyota ATF WS).
3. If the fluid appears dark or has a burnt smell, proceed to change the fluid.
4. Drain the old transmission fluid using a fluid pump or by removing the drain plug.
5. Replace the drain plug and refill the transmission with fresh fluid using a funnel.

3. Replace Transmission Filter

Tools Required: Socket set, torque wrench, gasket scraper.
Steps:
1. Remove the transmission pan bolts using a socket wrench.
2. Carefully lower the transmission pan and allow any remaining fluid to drain out.
3. Inspect the gasket surface; clean it if necessary.
4. Remove the old filter and replace it with a new one, ensuring it is seated properly.
5. Reinstall the transmission pan with a new gasket and torque the bolts to the manufacturer's specifications (typically 8-10 ft-lbs).

4. Inspect and Repair Electrical Components

Tools Required: Multimeter, wire connectors, electrical tape.
Steps:
1. Inspect the wiring harness connected to the transmission for any visible damage or corrosion.
2. Use a multimeter to test the transmission solenoids for resistance; replace any defective solenoids.
3. Ensure all connectors are secure and free of corrosion.

5. Reset Transmission Control Module (if applicable)

Tools Required: OBD-II scanner.
Steps:
1. Reconnect the battery.
2. Use the OBD-II scanner to clear any error codes related to the transmission.
3. Perform a quick test drive to ensure the transmission operates smoothly.