my Toyota Corolla E170 (2013-2019) engine light is on and it smells like gas, what should I do?

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

537 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix fuel system issues in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Fuel System

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on the fuel system.
•Allow the engine to cool before performing any repairs.

Symptoms

•Check engine light illuminated
•Strong gasoline odor
•Possible rough idle
•Decreased fuel efficiency
•Engine stalling during operation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific trouble codes.
2
Inspect the fuel lines and connections for any visible leaks or wear.
3
Check the fuel injectors for signs of leakage or malfunction.
4
Examine the fuel pressure regulator to ensure it is functioning correctly.
5
Inspect the EVAP system components for damage or blockages.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Flare-nut wrench
•Fuel line disconnect tool
•Torque wrench
•Jack and jack stands

Parts Required

•New fuel lines
•Fuel injectors (as needed)
•Fuel pressure regulator
•EVAP system components (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific trouble codes.
2
Inspect the fuel lines and connections for any visible leaks or wear.
3
Check the fuel injectors for signs of leakage or malfunction.
4
Examine the fuel pressure regulator to ensure it is functioning correctly.
5
Inspect the EVAP system components for damage or blockages.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Inspect and Replace Fuel Lines

Sub-steps:
1. Raise the vehicle using a jack and secure it with jack stands.
2. Visual inspection of all fuel lines; replace any that are cracked or leaking.
3. Use a flare-nut wrench to disconnect the fuel lines from the fuel rail and tank.
4. Install new fuel lines, ensuring proper routing and secure connections.
5. Tighten connections to manufacturer's torque specifications (usually around 15-20 ft-lbs).

3. Check and Replace Fuel Injectors

Sub-steps:
1. Remove the engine cover (if applicable) using a socket set.
2. Disconnect the electrical connectors from the fuel injectors.
3. Use a fuel line disconnect tool to remove the injectors from the fuel rail.
4. Inspect the O-rings for wear; replace injectors if they are leaking.
5. Reinstall the new or cleaned injectors, applying a small amount of engine oil to O-rings for easier installation.

4. Inspect and Replace Fuel Pressure Regulator

Sub-steps:
1. Locate the fuel pressure regulator (usually mounted on the fuel rail).
2. Disconnect the vacuum line and electrical connector from the regulator.
3. Remove the regulator by unscrewing the mounting bolts.
4. Install the new regulator, ensuring it seals properly.
5. Reconnect the vacuum line and electrical connector.

5. Check EVAP System

Sub-steps:
1. Access the EVAP canister, typically located under the vehicle near the fuel tank.
2. Inspect the hoses for cracks and ensure secure connections.
3. Replace any damaged components, including the canister if necessary.
4. Clear any codes with the OBD-II scanner after repairs.